【摘要】：目的本實驗通過傅里葉變換衰減全反射紅外光譜法,對不同厚度IPS E.max CAD玻璃陶瓷和不同光照模式作用下自粘接雙固化樹脂水門汀3M RelyX U200聚合程度進行對比分析,為臨床進行樹脂粘接操作提供一定的參考依據。方法實驗一:將RelyX U200注滿DSC氧化鋁坩堝(內徑6.5mm,高度1.5mm),制備試件50個,隨機分別接受Elipar S10 LED光固化燈傳統光照20s(TR)和延長光照40s(PR),每種光照模式按照介質厚度分為4個實驗組H1、H2、H3、H4(E.max CAD HT A3瓷片1mm~4mm厚度)和1個對照組H0(蓋玻片),總計10組,每組5個試件。37℃恒溫干燥避光保存24h后,應用傅里葉變換衰減全反射紅外光譜儀記錄RelyX U200固化前后的紅外光譜,記錄峰值,測算各組樹脂水門汀聚合轉化率(Degree of convertion,DC),并對統計數據進行雙因素方差分析。實驗二:將RelyX U200注滿DSC氧化鋁坩堝(內徑6.5mm,高度1.5mm),制備試件25個,隨機分為5組:實驗組IN1,IN2,IN3,IN4和對照組TR。透過E.max CAD HT A3瓷片(厚度1mm)分別接受Elipar S10 LED光固化燈IN1(光照2s+間歇30s+光照20s)、IN2(光照2s+間歇60s+光照20s)、IN3(光照2s+間歇90s+光照20s)、IN4(光照2s+間歇120s+光照20s)以及TR(光照20s)不同模式光照。37℃恒溫干燥避光保存24h后,應用傅里葉變換衰減全反射紅外光譜儀記錄RelyX U200固化前后的紅外光譜,記錄峰值,計算聚合轉化率,并對統計數據進行單因素方差分析、LSD-t組間比較以及獨立樣本t檢驗。結果1.隨著E.max CAD瓷片厚度增加,傳統光照模式(TR)和延長光照模式(PR)RelyX U200 DC%均逐漸下降,差異具有統計學意義(P0.05)。TR組DC%由35.46%(TRH0)下降到12.22%(TRH4),PR組則由39.24%(PRH0)下降到21.41%(PRH4)。相同瓷片厚度時,延長光照模式DC%高于傳統光照模式DC%(P0.05)。2.間歇光照模式下RelyX U200 DC%高于傳統光照模式,差異具有統計學意義(P0.05)。隨著間歇時長的延長(2min內),DC%由30.32%(IN1)逐漸上升至37.04%(IN4),組間差異具有統計學意義(P0.05)。結論1.隨著E.max CAD玻璃陶瓷厚度增加,RelyX U200的聚合程度降低,適當延長光照有助于聚合程度的提升。2.間歇光照模式下RelyX U200聚合程度較傳統光照模式高,2min內隨間歇時長延長升高。
[Abstract]:Objective to compare the degree of polymerization of self-bonded double-curing resin cement 3M RelyX U200 with different thickness of IPS E.max CAD glass ceramics and different illumination modes by Fourier transform attenuated total reflectance infrared spectroscopy (FTIR). To provide some reference for clinical operation of resin bonding. Methods experiment 1: RelyX U200 was filled with DSC alumina crucible (inner diameter 6.5mm, high 1.5mm), and 50 specimens were prepared. Each light pattern of Elipar S10 LED light curing lamp was randomly divided into 4 groups according to the thickness of medium according to the thickness of the medium. Each model was divided into 4 groups: H1H2H2H3H3H4 (E.max CAD HT A3 ceramic slice 1mm~4mm thickness) and a control group H0 (cover glass), a total of 10 groups. The infrared spectra of RelyX U200 before and after curing were recorded by Fourier transform attenuated total reflectance infrared spectrometer and the peak value was recorded. The conversion rate of resin cement polymerization (Degree of convertion,DC) was measured and the statistical data were analyzed by double factor analysis of variance (ANOVA). Experiment 2: RelyX U200 was filled with DSC alumina crucible (inner diameter 6.5mm, high 1.5mm), 25 specimens were prepared and randomly divided into five groups: experimental group IN1,IN2,IN3,IN4 and control group TR.. Elipar S10 LED light-curing lamp IN1 (20 s), IN2 (20 s), IN3 (20 s), IN4 (20 s) and TR (20 s) were treated by E.max CAD HT A3 (thickness 1mm). After 24 h storage at 37 鈩，

本文編號：2278785