本文選題：硅橡膠　切入點：印模技術　出處：《安徽醫科大學》2014年碩士論文　論文類型：學位論文

【摘要】：目的應用三維數字模型分析法，對硅橡膠的兩種印模方法的清晰度進行比較。 方法從10名志愿者中選取40顆健康的前磨牙作為試驗對象。用Silagum加成型硅橡膠對同一牙齒頰側排齦后進行一次印模法（Putty-wash技術）及二次印模法(Double mixing技術)取模后，灌制超硬石膏模型。用Dscan三維激光掃描儀對模型進行掃描，進而獲取模型的三維數據，通過專業的逆向工程軟件進行數字模型的修整、擬合，測量并比較兩種取模方法所制取模型在齦緣不同部位的齦溝寬度，以評價兩種取模方法的清晰度。 結果一次印模法與二次印模法所制取模型的齦溝寬度在齦緣中部及軸角部位的差異均具有統計學意義(p＜0.05)，二次印模法大于一次印模法；齦緣中部與軸角部位的齦溝寬度差異具有統計學意義(p＜0.05)，，齦緣中部大于軸角部位。 結論在相同條件下制取模型，硅橡膠二次印模法比一次印模法更清晰。
[Abstract]:Objective to compare the definition of silicone rubber with three-dimensional digital model analysis. Methods A total of 40 healthy premolars were selected from 10 volunteers. Putty-wash technique and double mixing technique were used to remove the gingival of the same tooth by using Silagum and silicone rubber. The superanhydrite model is made. The model is scanned by Dscan 3D laser scanner, and then the 3D data of the model is obtained, and the digital model is modified and fitted by professional reverse engineering software. The width of gingival sulcus in different parts of gingival margin was measured and compared to evaluate the definition of the two methods. Results the width of gingival sulcus in the middle of gingival margin and axial angle was significantly different between the primary impression method and the secondary impression method (p < 0.05), and the second impression method was larger than the primary impression method. There was significant difference in the width of gingival sulcus between the middle part of gingival margin and the position of axial angle (P < 0.05), and the middle part of gingival margin was larger than that of axial angle. Conclusion under the same conditions, the silicone rubber secondary impression method is more clear than the primary impression method.
【學位授予單位】：安徽醫科大學
【學位級別】：碩士
【學位授予年份】：2014
【分類號】：R783

【參考文獻】

相關期刊論文 前10條

1 張津京;劉玉華;呂培軍;趙一姣;;三維模型分析法評價不同排齦時間下的齦溝寬度[J];北京大學學報(醫學版);2011年01期

2 張小虎;歐建良;苑云;馬欽華;朱肇昆;于起峰;;投影輪廓線輔助下的堆場三維形貌攝影測量研究[J];光學學報;2011年06期

3 馮云枝;曾曉華;;不同排齦藥物的排齦效果觀察[J];華西口腔醫學雜志;2011年01期

4 武迎春;曹益平;肖焱山;;一種主動修正投影光柵提高在線三維測量精度的方法[J];中國激光;2011年09期

5 劉洪臣,王燕一,王東勝,江南;口腔修復技術進展(一)[J];口腔頜面修復學雜志;2000年02期

6 胡航;張正儀;楊艷麗;陳育松;;加聚型硅橡膠一次法、兩次法印模三維精度研究[J];口腔醫學;2007年08期

7 王華蓉,岳莉,李勇,趙云鳳;間接印模法對CAD/CAM全瓷底層冠適合性影響[J];臨床口腔醫學雜志;2003年03期

8 黃慧;李靜;張富強;;5種著色氧化鋯陶瓷的細胞毒性評價[J];臨床口腔醫學雜志;2007年07期

9 杜方

本文編號：1577948