【摘要】：目的:探討幾種表面處理方法對氧化鋯修復體粘接強度的影響,為提高氧化鋯修復體的粘接力提供依據。方法:加工10mm×10mm×2mm釔穩定氧化鋯瓷坯60件,根據表面處理方法不同將試件分成噴砂組、硅涂層組、Z-PRIME Plus組、噴砂+Z-PRIME Plus組、噴砂+硅涂層組和硅涂層膠+Z-PRIME Plus組,每組10件。使用通用型粘接劑Scotchbond~(TM) Universal制作氧化鋯-樹脂粘接樣本,在37℃水浴中儲存24h后采用萬能力學試驗機測試其剪切強度,體視顯微鏡記錄樣品斷裂模式,各組斷裂樣品隨機抽取1件,在掃描電子顯微鏡下觀察其表面形貌。結果:Z-PRIME Plus組試件所測得的剪切強度明顯高于其他組(P0.05)。斷裂模式觀察,粘接破壞主要出現在噴砂、硅涂層、噴砂+硅涂層和硅涂層+Z-PRIME Plus組試件中。噴砂+Z-PRIME Plus組試件混合破壞4例,噴砂+硅涂層組試件混合破壞8例;各組試件均未出現內聚破壞。掃描電鏡下觀察,噴砂、Z-PRIME Plus和噴砂+Z-PRIME Plus組試件斷裂面發生在粘接劑-氧化鋯界面,硅涂層、硅涂層+Z-PRIME Plus組試件斷裂面發生在硅涂層-氧化鋯界面,噴砂+硅涂層組試件斷裂面部分發生在硅涂層-粘接劑界面。結論:Z-PRIME Plus用于氧化鋯表面預處理可以明顯提高其與樹脂的粘接強度。
[Abstract]:Objective: To study the effect of several kinds of surface treatment on the bonding strength of the repair body of the oxidized silicon oxide, and to provide the basis for improving the adhesive force of the oxygen-oxidizing agent. Method:60 pieces of 10-mm,10-mm and 2-mm high-pressure stable oxidation-resistant porcelain were processed, and the test pieces were divided into sand-blasting group, silicon coating group, Z-PRIME Plus group, sand-blasting + Z-PRIME Plus group, sand-blasting + silicon coating group and silicon-coating adhesive + Z-PRIME Plus group according to the surface treatment method. using a universal adhesive, Scotch-(TM) Universal, to make an oxidized-resin adhesive sample, storing the sample in a water bath at a temperature of 37 DEG C for 24 hours, testing the shear strength by using a universal mechanical testing machine, recording the fracture mode of the sample according to a stereomicroscope, and randomly extracting one piece of fracture samples in each group, The surface morphology was observed under a scanning electron microscope. Results: The shear strength of Z-PRIME plus group was significantly higher than that of other groups (P0.05). The fracture mode was observed and the adhesion failure mainly occurred in the sandblasting, silicon coating, sandblasting + silicon coating and the silicon coating + Z-PRIME Plus group test piece. In the sand-blasting + Z-PRIME Plus group,4 cases were mixed and destroyed, and 8 cases were mixed and destroyed by the sand-blasting + silicon coating group, and no cohesive failure occurred in each group of test pieces. The fracture surface of the test piece of the sand-blasting, Z-PRIME Plus and the sand-blasting + Z-PRIME Plus group was observed under the scanning electron microscope, and the fracture surface of the test piece on the adhesive-oxidation interface, the silicon coating, the silicon coating and the Z-PRIME Plus group occurred on the silicon coating-oxidation interface, The part of the fracture surface of the sand-blasted + silicon coating group occurred on the silicon coating-adhesive interface. Conclusion: Z-PRIME Plus can obviously improve the bonding strength of Z-PRIME plus the resin.
【作者單位】： 吉林大學口腔醫院VIP綜合科吉林省牙發育及頜骨重塑與再生重點實驗室;
【基金】：吉林省財政廳衛生專項項目資助課題(3D515R763431)
【分類號】：R783.1

【相似文獻】

相關期刊論文 前10條

1 馬紅;章非敏;王娟;孫衛斌;謝海峰;;納米硅涂層改性牙科氧化鋁基陶瓷生物相容性研究[J];南京醫科大學學報(自然科學版);2007年05期

2 朱曄;謝海峰;章非敏;;納米硅涂層對玻璃滲透氧化鋁陶瓷抗破裂強度的影響[J];國際口腔醫學雜志;2011年03期

3 張麗萍;葛文章;;熔膠凝膠納米硅涂層對氧化鋯全瓷固定橋抗折裂能力的影響[J];中國醫藥指南;2013年28期

4 謝海峰;章非敏;陳晨;袁秀祥;;納米硅涂層對玻璃滲透氧化鋁陶瓷粘結強度的影響[J];臨床口腔醫學雜志;2006年07期

5 劉玲;噴砂和硅涂層對聚合體玻璃復合物對鑄鈦結合強度的影響[J];國外醫學.生物醫學工程分冊;2000年03期

6 王曉菲;謝海峰;章非敏;;疏水性硅涂層對牙科氧化鋯陶瓷的表面改性研究[J];口腔生物醫學;2011年01期

7 王瑜;章非敏;謝海峰;;硅涂層對牙科氧化鋁陶瓷與樹脂粘結強度的影響[J];中華口腔醫學雜志;2007年12期

8 周淑;王瑜;章非敏;光寒冰;;納米硅涂層對鈦瓷結合強度的影響[J];華西口腔醫學雜志;2009年03期

9 徐春華;耿建平;;表面硅涂層改性對氧化鋯陶瓷與樹脂水門汀粘結強度的影響[J];口腔醫學;2012年11期

10 董紅;余和東;龐光明;張敬陽;;表面硅涂層改性對氧化鋯陶瓷與樹脂水門汀粘結強度的影響[J];口腔醫學研究;2013年05期

相關會議論文 前1條

1 謝海峰;何峰;殷雪萌;王學;章非敏;;納米硅涂層對玻璃滲透氧化鋁陶瓷破裂強度的影響[A];第六次全國口腔修復學學術會議論文摘要匯編[C];2009年

相關碩士學位論文 前2條

1 謝海峰;溶膠凝膠法硅涂層對陶瓷黏結強度影響的基礎研究[D];南京醫科大學;2007年

2 王瑜;納米硅涂層對牙科高強度陶瓷粘結強度的影響[D];南京醫科大學;2008年

，

本文編號：2435698