本文選題：牙科印模技術 + 成像　； 參考：《北京大學學報(醫學版)》2015年01期

【摘要】：目的:研究模擬口腔取模環境下TRIOS數字印模的精密度,并與口外模型掃描的精密度比較。方法:制作6個#14~#17樹脂牙列,其中#16為離體牙的全瓷冠預備體。對樹脂牙列分別進行:(1)硅橡膠取印模,灌注石膏模型,3Shape D700模型掃描儀重復掃描10次;(2)固定于仿頭模內,3Shape TRIOS口內掃描儀重復掃描10次。Geomagic Qualify12.0對重復掃描數據兩兩進行最佳擬合對齊和3D比較,分別輸出配準數據間的平均偏差(averaged errors,AE)和差異分布彩圖。秩和檢驗定量分析數字印模組與模型組AE的差異,根據差異分布彩圖定性描述偏差分布特征。結果:數字印模組AE均數為7.058 281μm,高于模型組4.092 363μm,差異具有統計學意義(P0.05),但是數字印模組AE的均數和中位數均小于10μm,表明掃描數據間一致性良好。模型組偏差分布均勻,數字印模組偏差較大區域主要分布于肩臺及鄰面區域。結論:TRIOS數字印模精密度良好,可達到臨床應用要求,預備體肩臺及鄰面區域為掃描的難點。
[Abstract]:Aim: to study the precision of TRIOS digital impression in simulated oral cavity and compare it with that of external model. Methods: six #14 #17 resin dentitions were made, of which #16 was the all-ceramic crown preparation for isolated teeth. The resin dentition was made with 1% of the silicone rubber and the impression was obtained by using silicone rubber. The 3Shape D700 model scanner was fixed to the 3Shape TRIOS mouth scanner for 10 times. Geomagic Qualify12.0 performed the best fitting alignment and 3D comparison of the repeated scanning data. The average deviation between the registration data and the difference distribution color map are outputted respectively. The difference of AE between digital printing module and model group was quantitatively analyzed by rank sum test, and the deviation distribution characteristics were described qualitatively according to the difference distribution color map. Results: the average AE of digital printing module group was 7.058 281 渭 m, which was higher than that of model group 4.092 363 渭 m, the difference was statistically significant (P 0.05), but the mean number and median of AE in digital printing module group were less than 10 渭 m, which indicated that the scanning data were consistent. The deviation distribution of the model group is uniform, and the large deviation area of the digital printing module is mainly distributed in the shoulder platform and adjacent area. Conclusion the precision of the digital impression is good and it can meet the requirement of clinical application. The shoulder plate and adjacent area of the prepared body are the difficult points in scanning.
【作者單位】： 北京大學口腔醫學院·口腔醫院修復科;深圳愛爾創科技股份有限公司;清華大學材料科學與工程系;北京大學口腔醫學院·口腔醫院綜合科;口腔數字化醫療技術和材料國家工程實驗室;
【分類號】：TP391.7;R783.3

【參考文獻】

相關期刊論文 前3條

1 呂培軍;孫玉春;;口腔修復計算機輔助設計/制作的過去、現在和將來[J];北京大學學報(醫學版);2010年01期

2 Richard D. Stutes;;椅旁CAD/CAN牙科修復系統的歷史與臨床應用現狀(英文)[J];上海口腔醫學;2006年05期

3 徐明明;劉峰;;CAD/CAM技術在口腔修復中的應用 數字印模技術[J];中國實用口腔科雜志;2013年06期

【共引文獻】

相關期刊論文 前10條

1 董穎韜;王曉燕;高學軍;;樹脂粘固劑厚度對CAD/CAM長石質陶瓷斷裂性能的影響[J];北京大學學報(醫學版);2012年02期

2 楊彥春;肖利;周繼祥;;CEREC全瓷嵌體修復楔狀缺損后牙體抗折強度的實驗研究[J];第三軍醫大學學報;2010年11期

3 孔衛東;林久祥;林巍;徐浩;張華;黃偉紅;;個體化舌側矯治器的初步實驗研究[J];國際口腔醫學雜志;2011年05期

4 張磊;葉紅強;楊振宇;周艷光;孫玉春;趙一姣;周永勝;;個性化牙種植體三維數字模型的建立[J];北京大學學報(醫學版);2013年01期

5 陳志宇;李雅;陳倩;鄧旭亮;王新知;;基于印模掃描數據CAD/CAM一體化纖維樁核的密合度觀察[J];北京口腔醫學;2013年04期

6 雷小寶;謝峰;廖文和;鄭侃;趙吉文;;Design and Performance Analysis of Small Denture Machining Equipment[J];Journal of Donghua University(English Edition);2013年03期

7 肖靜;滕偉;;三維數字化掃描在口腔修復領域中的應用[J];國際口腔醫學雜志;2014年01期

8 管東華;黃建生;黃曉虹;周俏儀;馬s，

本文編號：1985282