發布時間：2018-03-20 22:14

  本文選題：義齒穩固劑　切入點：全口義齒　出處：《上�？谇会t(yī)學》2014年01期 　論文類型：期刊論文

【摘要】：目的:針對Atwood 3級無牙下頜牙槽嵴制作下半口義齒,分析其使用義齒穩固劑前、后,在正中咬合力加載時牙槽骨的應力分布情況。方法:應用三維光彈實驗方法,在Atwood 3級無牙頜環氧樹脂光彈模型上制作全口義齒,并在下半口義齒組織面內使用和不使用義齒穩固劑,進行正中咬合下應力加載凍結,比較其應力分布。結果:下半口使用義齒穩固劑后,正中咬合加載時,牙槽嵴頂和頰、舌側應力分布更均勻,牙槽嵴頂較不使用穩固劑應力明顯上升。結論:臨床上對于Atwood 3級牙槽嵴患者,采用下半口義齒修復時,使用義齒穩固劑不僅可以增加義齒穩定性,還可使下頜后牙牙槽嵴的主副承托區應力分布更趨均勻,減少應力集中導致的局部壓痛。
[Abstract]:Objective: to analyze the stress distribution of alveolar bone of Atwood grade 3 edentulous mandibular alveolar ridge before and after using denture stabilizer. Methods: three dimensional photoelastic method was used. The complete denture was made on the Atwood grade 3 edentulous epoxy resin photoelastic model, and the stress loading freezing was carried out in the lower half denture with or without denture stabilizer. Results: the stress distribution on the top of alveolar ridge and on cheek and tongue was more uniform when the middle part of denture was loaded with denture stabilizer. Conclusion: for Atwood grade 3 alveolar ridge patients, the application of denture stabilizer can not only increase the stability of denture, but also increase the stability of denture. The stress distribution in the primary and secondary bearing region of the alveolar ridge of the mandibular posterior alveolar ridge is more uniform and the local tenderness caused by the stress concentration can be reduced.
【作者單位】： 上海市口腔病防治院;上海應用技術學院機械與自動化學院;
【分類號】：R783.6

【參考文獻】

相關期刊論文 前10條

1 張曉南;辜向東;陳新民;;Apac新型義齒穩固劑對牙槽嵴低平患者全口義齒滿意度的影響[J];重慶醫學;2009年23期

2 王昆潤;;無牙下頜粘膜的厚度[J];國外醫學.口腔醫學分冊;1988年02期

3 張鳳;李希庭;魏素華;;義齒穩固劑的研究進展[J];國際口腔醫學雜志;2007年06期

4 姚月玲;周敬行;汪文駿;;牙頜三維光彈模型的制作法[J];口腔醫學縱橫;1991年01期

5 佘文s，

本文編號：1641016