小凈距交叉隧道爆破振動控制技術研究
發布時間：2018-11-20 19:31
【摘要】：本論文以中川城際鐵路與蘭州北編組站聯絡線北環隧道上穿蘭州樞紐工程紅山頂隧道為依托工程，從理論分析、爆破振動監測和數值模擬等幾個方面對小凈距空間交叉隧道施工爆破技術及控制措施進行系統研究，為設計、施工決策提供基礎資料和理論技術支持，以保證北環隧道的成功修建，并為其它類似地質條件下的隧道工程建設提供有益的參考。主要研究內容及其結論如下： (1)根據現場隧道爆破振動監測得到的振動速度和混凝土動應變數據，進行線性擬合得到了振動速度與動應變的關系，基于近接施工容許拉應力增量控制標準，確定本工程采用爆破振動安全振速控制標準為7.0cm/s。 (2)依據爆破安全規程及已有小凈距隧道施工研究資料，通過薩道夫斯基公式確定了北環隧道重點監測范圍為距交叉點±20m�；诎踩紤]取三個方向的總合成速度作為爆破振動振速控制標準，新建北環隧道交叉斷面±20m范圍內爆破施工時既有隧道最大振速為5.89cm/s，小于擬定的爆破振動安全速度。 (3)通過大量文獻及現場實測數據分析，爆破振動強度主要受地質條件、爆心距、裝藥量、爆破條件（爆破位置、臨空面條件）等多個方面影響。在薩道夫斯基公式的基礎上，并擬合得到了適用于北環隧道的爆破振動經驗公式，將掏槽爆破作為爆破振動控制重點，重點監測。 (4)對爆破振動波型圖進行頻譜分析和主頻分布分析，經過傅里葉變換，獲得典型的北環隧道爆破振動信號頻譜圖，確定了振動波主頻域的分布范圍�；诒瓢踩�(guī)程，將主振頻率作為爆破振動控制標準的判據，需要嚴格控制爆破振動波頻率遠離結構自身頻率，避免由于共振作用造成的損害。 (5)基于爆破振動強度的影響因素，對原有爆破方案在通過小凈距影響區域時進行調整，通過修改鉆孔設計，控制裝藥量，增加起爆次數，，減小開挖進尺，選擇合理的雷管起爆時差等方法，將爆破振動影響降低到最低限度。 (6)通過ANSYS分析軟件，建立小凈距立體交叉隧道的三維模型。通過數值模擬計算，上臺階掏槽爆破時既有隧道的最大振速小于7cm/s的振速控制值。既有隧道交叉斷面襯砌拉壓應力和拉壓應力增量也都滿足規范要求，說明在爆破過程中，既有隧道襯砌結構安全可靠。 (7)采用ANSYS有限元軟件模擬交叉段前后新建隧道臺階法施工時掏槽爆破對既有隧道的動力響應。通過振動速度、應力的大小來判斷爆破過程中既有隧道襯砌結構安全性，既有隧道襯砌最大振動小于7cm/s的安全振速，襯砌最小抗壓、抗拉安全系數和拉壓應力增量也都滿足安全性要求。
[Abstract]:Based on the project of Zhongchuan Intercity Railway and the North Ring Tunnel of Lanzhou North marshalling Station, this paper takes the Hongshan Tunnel, a project of Lanzhou hub, as the basis of theoretical analysis. Blasting vibration monitoring and numerical simulation are used to systematically study the blasting technology and control measures in the construction of small clear-spaced space crossing tunnel, which provides basic data and theoretical and technical support for design and construction decision. In order to ensure the successful construction of the North Ring Tunnel, and to provide a useful reference for other similar geological conditions of the tunnel construction. The main research contents and conclusions are as follows: (1) the relationship between vibration velocity and dynamic strain is obtained by linear fitting according to the vibration velocity and dynamic strain data obtained from field blasting vibration monitoring. Based on the control standard of allowable tensile stress increment in near-connection construction, it is determined that the safe vibration velocity control standard of blasting vibration is 7.0 cm / s. (2) on the basis of blasting safety regulations and the existing research data of small clear distance tunnel construction, the critical monitoring range of North Ring Tunnel is determined to be 鹵20m from intersection point by Saadolski formula. Based on the safety considerations, the total synthetic velocity in three directions is taken as the control standard of blasting vibration velocity, and the maximum vibration velocity of the existing tunnel is 5.89 cm / s when blasting is constructed in the range of 鹵20m cross section of the new North Ring Tunnel, and the maximum vibration velocity of the existing tunnel is 5.89 cm / s. Less than the proposed safety speed of blasting vibration. (3) through the analysis of a large number of documents and field measured data, the vibration intensity of blasting is mainly affected by geological conditions, the distance between the blasting centers, the charge quantity, the blasting conditions (the blasting position, the condition of the face near the air), and so on. On the basis of Sadolski's formula and fitting, the empirical formula of blasting vibration suitable for North Ring Tunnel is obtained. Cutting blasting is regarded as the key point of blasting vibration control and monitoring. (4) the spectrum analysis and main frequency distribution analysis of blasting vibration wave pattern are carried out. Through Fourier transform, the typical spectrum chart of blasting vibration signal of North Ring Tunnel is obtained, and the distribution range of main frequency domain of vibration wave is determined. Based on the blasting safety regulations, the main vibration frequency is regarded as the criterion of blasting vibration control standard. It is necessary to strictly control the frequency of blasting vibration wave to avoid the damage caused by resonance. (5) based on the influence factors of blasting vibration intensity, the original blasting scheme is adjusted when passing through the area affected by small net distance. By modifying the borehole design, the charge quantity is controlled, the number of detonation is increased, and the excavation advance is reduced. The blasting vibration effect is reduced to the minimum by selecting reasonable detonator time difference and other methods. (6) the three-dimensional model of cross tunnel with small net distance is established by ANSYS software. By numerical simulation, the maximum vibration velocity of existing tunnel is smaller than that of 7cm/s. Both the tensile and compressive stress and the increment of the tensile and compressive stress of the cross-section lining of the existing tunnel meet the requirements of the code, which shows that the lining structure of the existing tunnel is safe and reliable during blasting. (7) ANSYS finite element software is used to simulate the dynamic response of cutting blasting to the existing tunnel during the step construction of the new tunnel before and after the cross section. The safety of existing tunnel lining is judged by vibration speed and stress. The maximum vibration of existing tunnel lining is less than that of 7cm/s, and the minimum pressure of lining is obtained. The safety factor of tension and the increment of tension and compression stress also meet the safety requirements.
【學位授予單位】：蘭州交通大學
【學位級別】：碩士
【學位授予年份】：2014
【分類號】：U455.6
[Abstract]:Based on the project of Zhongchuan Intercity Railway and the North Ring Tunnel of Lanzhou North marshalling Station, this paper takes the Hongshan Tunnel, a project of Lanzhou hub, as the basis of theoretical analysis. Blasting vibration monitoring and numerical simulation are used to systematically study the blasting technology and control measures in the construction of small clear-spaced space crossing tunnel, which provides basic data and theoretical and technical support for design and construction decision. In order to ensure the successful construction of the North Ring Tunnel, and to provide a useful reference for other similar geological conditions of the tunnel construction. The main research contents and conclusions are as follows: (1) the relationship between vibration velocity and dynamic strain is obtained by linear fitting according to the vibration velocity and dynamic strain data obtained from field blasting vibration monitoring. Based on the control standard of allowable tensile stress increment in near-connection construction, it is determined that the safe vibration velocity control standard of blasting vibration is 7.0 cm / s. (2) on the basis of blasting safety regulations and the existing research data of small clear distance tunnel construction, the critical monitoring range of North Ring Tunnel is determined to be 鹵20m from intersection point by Saadolski formula. Based on the safety considerations, the total synthetic velocity in three directions is taken as the control standard of blasting vibration velocity, and the maximum vibration velocity of the existing tunnel is 5.89 cm / s when blasting is constructed in the range of 鹵20m cross section of the new North Ring Tunnel, and the maximum vibration velocity of the existing tunnel is 5.89 cm / s. Less than the proposed safety speed of blasting vibration. (3) through the analysis of a large number of documents and field measured data, the vibration intensity of blasting is mainly affected by geological conditions, the distance between the blasting centers, the charge quantity, the blasting conditions (the blasting position, the condition of the face near the air), and so on. On the basis of Sadolski's formula and fitting, the empirical formula of blasting vibration suitable for North Ring Tunnel is obtained. Cutting blasting is regarded as the key point of blasting vibration control and monitoring. (4) the spectrum analysis and main frequency distribution analysis of blasting vibration wave pattern are carried out. Through Fourier transform, the typical spectrum chart of blasting vibration signal of North Ring Tunnel is obtained, and the distribution range of main frequency domain of vibration wave is determined. Based on the blasting safety regulations, the main vibration frequency is regarded as the criterion of blasting vibration control standard. It is necessary to strictly control the frequency of blasting vibration wave to avoid the damage caused by resonance. (5) based on the influence factors of blasting vibration intensity, the original blasting scheme is adjusted when passing through the area affected by small net distance. By modifying the borehole design, the charge quantity is controlled, the number of detonation is increased, and the excavation advance is reduced. The blasting vibration effect is reduced to the minimum by selecting reasonable detonator time difference and other methods. (6) the three-dimensional model of cross tunnel with small net distance is established by ANSYS software. By numerical simulation, the maximum vibration velocity of existing tunnel is smaller than that of 7cm/s. Both the tensile and compressive stress and the increment of the tensile and compressive stress of the cross-section lining of the existing tunnel meet the requirements of the code, which shows that the lining structure of the existing tunnel is safe and reliable during blasting. (7) ANSYS finite element software is used to simulate the dynamic response of cutting blasting to the existing tunnel during the step construction of the new tunnel before and after the cross section. The safety of existing tunnel lining is judged by vibration speed and stress. The maximum vibration of existing tunnel lining is less than that of 7cm/s, and the minimum pressure of lining is obtained. The safety factor of tension and the increment of tension and compression stress also meet the safety requirements.
【學位授予單位】：蘭州交通大學
【學位級別】：碩士
【學位授予年份】：2014
【分類號】：U455.6
【相似文獻】
相關期刊論文 前10條
1 葉顯亮;;隧道爆破施工對附近房屋的振動監測與影響分析[J];貴州大學學報(自然科學版);2010年02期
2 謝興洋;毛彪;;方家山核電隧道爆破工程概述[J];價值工程;2011年17期
3 程圍峰;梁旭;王振宇;;隧道爆破施工對鄰近輸油管道的影響評價[J];石油工程建設;2011年04期
4 馮義;趙先鵬;馬菖林;陳壽根;;臨近隧道爆破研究的現行問題分析[J];公路隧道;2011年03期
5 賈世平;;隧道爆破施工對某高壓油管的影響分析[J];土工基礎;2012年05期
6 吳開才;;實例探析瓦斯隧道爆破設計[J];黑龍江交通科技;2013年09期
7 曹增福,李會祥;使用多種爆破器材進行隧道爆破[J];鐵道工程學報;1985年04期
8 王華;市區的隧道爆破工程[J];隧道譯叢;1994年03期
9 謝泰極;隧道爆破與直眼掏槽(續)[J];爆破器材;1997年04期
10 李樹良;對鄰近隧道爆破施工的幾點體會[J];鐵道建筑技術;1998年04期
相關會議論文 前7條
1 鄭大榕;;控制隧道爆破振動研究[A];中國土木工程學會隧道及地下工程學會第八屆年會論文集[C];1994年
2 楊年華;魏志韜;;隧道爆破中乳化炸藥泵送裝填技術及其應用[A];鐵路長大隧道設計施工技術研討會論文集[C];2004年
3 常翔;;侯月鐵路云臺山隧道爆破技術安全管理淺談[A];爆破安全技術與管理研討會論文集[C];2006年
4 王世n
本文編號：2345780
本文鏈接：http://sikaile.net/kejilunwen/jiaotonggongchenglunwen/2345780.html
最近更新
教材專著
