發布時間：2018-04-19 08:42

  本文選題：風沙環境 + 鋼結構涂層��； 參考：《應用力學學報》2014年06期

【摘要】：利用接觸力學理論和三維有限元分析了鋼結構受到風沙粒子沖擊后其涂層表面接觸區應力、涂層內部應力、涂層與基體界面上應力的分布規律。分析結果表明:涂層表面徑向應力在接觸中心出現最大壓應力,在接觸區邊緣出現最大拉應力,且在接觸區邊緣易發生環狀撕裂破壞;在涂層內部,涂層對Z向應力的承受力較好;涂層內部剪應力的最大值出現在碰撞接觸點的左下方和右下方,這兩個位置易受到剪切破壞,在接觸點和剪應力最大值之間的剪應力變化速度較大;涂層與基體界面上r/h為0~0.4時,Z向應力變化較小;在r/h為0.4~1時,Z向應力劇烈減小;r/h1時,Z向應力基本保持不變;涂層與基體界面上剪應力最大值出現在沖擊點附近,且沖擊點附近剪應力變化較大,易引起剪切撕裂破壞。
[Abstract]:Based on the contact mechanics theory and three-dimensional finite element method, the stress distribution in the surface contact zone, the internal stress of the coating and the stress at the interface between the coating and the substrate were analyzed.The results show that the radial stress of the coating surface appears maximum compressive stress at the contact center, the maximum tensile stress occurs at the edge of the contact zone, and the ring tearing failure occurs easily at the edge of the contact zone, and within the coating,The maximum shear stress of the coating appears in the lower left and lower right of the impact contact point, which is vulnerable to shear failure.The variation rate of shear stress between the contact point and the maximum shear stress is larger, the variation of Z direction stress is small when r / h is 0 / 0.4 at the interface between coating and substrate, and the change of Z direction stress is almost unchanged when r / h is 0. 4 ~ 1% and r / h is 0. 4 ~ 1 ~ 1 / r ~ (-1).The maximum shear stress at the interface between the coating and the substrate appears near the impact point, and the shear stress near the impact point changes greatly, which easily leads to shear tearing failure.
【作者單位】： 內蒙古工業大學土木工程學院;
【基金】：國家自然科學基金(11162011) 內蒙古自治區自然學基金(2009 MS0706)
【分類號】：TU391

【參考文獻】

相關期刊論文 前2條

1 湯姆.貝爾;Y.Sun;H.Dong;;表面工程系統接觸力學模型[J];中國表面工程;2007年02期

2 張茜;蔡宗熙;黃干云;侯振德;亢一瀾;鄭琳;;盾構刀盤系統界面載荷力學表征與近似計算模型[J];力學學報;2012年05期

【共引文獻】

相關期刊論文 前3條

1 秦林;趙琪;楊昆昆;唐賓;;TC4鈦合金齒輪表面滲鉬合金化后的組織與性能[J];機械工程材料;2013年10期

2 郝，

本文編號：1772384