本文選題：聚醚醚酮 + 表面處理　； 參考：《口腔醫學研究》2017年08期

【摘要】：目的:研究經過不同表面處理后的聚醚醚酮與飾面樹脂間粘結強度的變化。實驗方法:將聚醚醚酮樣品隨機分為4組進行表面處理:98%濃硫酸酸蝕組,粘結劑處理組,98%濃硫酸酸蝕+粘結劑處理組和未處理對照組。各處理組再隨機分為2個亞組粘結飾面樹脂:GC Gradia組,Ceramage組。每個亞組隨機選出一半樣品用37℃蒸餾水浸泡24h,其余樣品冷熱循環10000次后,測量樣品的剪切粘結強度,SPSS軟件統計分析數據;體視顯微鏡檢查樣品斷裂界面,統計粘結失敗類型。結果:各表面處理實驗組與空白對照組之間均存在統計學差異,經硫酸酸蝕處理的聚醚醚酮與Ceramage硬質樹脂的粘結強度最高(19.38±5.34)MPa,且與其他實驗組有統計學差異(P0.05)。在冷熱循環后,除粘結Gradia Direct樹脂的濃硫酸+粘結劑處理組外,其余實驗組的粘結強度明顯降低(P0.05)。結論:濃硫酸酸蝕與自酸蝕粘結劑均能提高聚醚醚酮與飾面樹脂的粘結強度,Gradia Direct飾面樹脂與經濃硫酸+粘結劑處理的聚醚醚酮表面可形成穩定的粘結作用。
[Abstract]:Objective: to study the change of bond strength between polyether ether ketone and finishing resin after different surface treatment. Methods: the samples of polyether ether ketone were randomly divided into 4 groups: surface treatment group with 0 98% concentrated sulphate acid etching group, binder treatment group with 98% concentrated sulphate acid etching binder group and untreated control group. Each treatment group was randomly divided into two subgroups: GC Gradia group and Ceramage group. Half of the samples were immersed in distilled water at 37 鈩，

本文編號：1784573