【摘要】：針對W波段波導縫隙天線加工難度高、加工后縫隙尺寸不易修改的問題,提出了一種改進型縫隙電導函數提取方法.首先,根據工藝可實現性,設定合理的波導輻射面壁厚和縫隙寬度;然后,應用HFSS軟件計算出不同縫隙切入深度和縫隙傾斜角度的縫隙電導值;最后,利用Matlab軟件擬合出電導函數曲線,并進行階梯狀的分段近似,以簡化加工工藝復雜度.基于優化設計結果,加工出4套天線樣品,采用緊縮場測試方法對天線進行輻射方向圖測量.結果表明,在75~79 GHz的頻帶內,天線增益均大于23.5 d Bi,E面3 d B波束寬度為1.2°,旁瓣電平低于-20 d B.當頻率從75 GHz掃描至79 GHz時,E面3 d B波束覆蓋范圍為5.5°.4套天線的性能測試結果展現出較好的一致性,從而驗證了設計方法的正確性和有效性.
[Abstract]:In order to solve the difficulty of machining W-band waveguide slot antenna and the difficulty of modifying slot size after machining, an improved slot conductance function extraction method is proposed. Firstly, according to the realization of the process, the wall thickness and slot width of the waveguide radiation surface are set reasonably, and then, the gap conductivity values of different slit depth and slot tilt angle are calculated by HFSS software. Finally, the curve of conductivity function is fitted by Matlab software, and the step-like piecewise approximation is carried out to simplify the complexity of machining process. Based on the optimized design results, four sets of antenna samples were fabricated, and the radiation pattern of the antenna was measured by the method of compact field measurement. The results show that the gain of the antenna is greater than 23.5 d Bi, E plane 3 dB beamwidth and the sidelobe level is lower than-20 dB in the frequency band of 75 / 79 GHz. When the frequency range is from 75 GHz to 79 GHz, the 3 dB beam coverage of the E plane is 5.5 擄. The performance test results of 4 sets of antennas show good consistency, thus validating the correctness and effectiveness of the design method.
【作者單位】： 東南大學毫米波國家重點實驗室;
【分類號】：TN823.24

【相似文獻】

相關期刊論文 前10條

1 田力人;;高增益低旁瓣天線陣的綜合技術[J];航空學報;1979年03期

2 萬偉;黃景熙;胡市明;;高增益低旁瓣天線陣的綜合技術[J];西北工業大學學報;1979年01期

3 陳述泉;;用于毫米波的低旁瓣小天線[J];電訊技術;1983年04期

4 于立民,盧振武;低旁瓣毫米波衍射天線的設計[J];紅外與毫米波學報;2000年06期

5 宋凱歌;甘泉;唐斌;;一種低旁瓣數字波束形成方法[J];信號處理;2009年05期

6 毛仁麟;;警戒雷達用低旁瓣拋物柱面天線[J];現代雷達;1982年01期

7 徐振華;黃建國;王秋紅;裴媈;;相位錐化低旁瓣和差波束方向圖合成新方法[J];兵工學報;2011年03期

8 賈偉娜;劉順蘭;;基于二次組陣的低旁瓣波束形成的修正算法[J];電子技術應用;2013年01期

9 劉豫晉,陳春紅;微帶低旁瓣和后瓣天線設計[J];電子工程師;2003年10期

10 任超;吳嗣亮;王菊;;基于空時二維結構的低旁瓣寬帶波束形成[J];系統工程與電子技術;2008年03期

相關會議論文 前1條

1 殷興輝;徐之材;彭樹生;;極低旁瓣輻射計天線[A];1995年全國微波會議論文集（上冊）[C];1995年

相關碩士學位論文 前1條

1 郭金瑞;波束域特征空間波束形成及其方向圖低旁瓣實現[D];安徽大學;2011年

，

本文編號：2464809