【摘要】：隨著工業現場通信總線技術的發展,PROFINET逐漸成為了諸多工業設備之間相互通信的主流技術。而目前工業現場所廣泛使用的傳感器、執行器、智能儀器儀表等,多通過內嵌單片機提供串行接口,實現與外部系統的串行通信。因此,通過研發一種PROFINET網關,該網關可實現將嵌有Modbus協議的設備通過RS-485接入PROFINET網絡,具有重要意義。本文根據工控現場通信需求,通過對PROFINET協議和Modbus協議以及PROFINET網關技術的研究與分析。采用西門子提供的工業以太網專用器件系列的ERTEC 200P芯片作為主理器,同時外擴了高速大容量SDRAM存儲器、NOR Flash存儲器及其他接口電路,形成基于ERTEC 200P的硬件板。在該硬件板上運行e Cos嵌入式實時操作系統、PROFINET協議棧,并在協議棧上層做應用開發。設計一款基于芯片STM32F103VET6的拓展板,在拓展板上運行Modbus協議主站程序,拓展板提供RS-485與工業現場設備連接,在拓展板上做應用開發。基于ERTEC 200P的硬件板與基于STM32F103VET6的拓展板通過11路GPIO連接,共同組成PROFINET網關的硬件。最后,本文通過搭建硬軟件平臺,對嵌入Modbus協議的設備與嵌入PROFINET協議的設備的通信交互進行了軟硬件聯機調試,并針對該系統性能指標進行了實驗測試。測試結果:從Modbus協議從站端發送數據,PROFINET協議端能接收到對應的數據;從PROFINET協議端發送數據,Modbus協議從站端能接收到對應的數據,具有診斷功能,完成了該網關的功能性研制,具有一定的實用價值。
[Abstract]:With the development of industrial field communication bus technology, PROFINET has gradually become the mainstream technology of communication between many industrial equipment. At present, the sensors, actuators, intelligent instruments and so on, which are widely used in the industrial field, provide the serial interface through embedded single-chip microcomputer to realize the serial communication with the external system. Therefore, through the development of a PROFINET gateway, it is of great significance that the devices embedded with Modbus protocol can be connected to the PROFINET network through RS-485. According to the requirements of industrial control field communication, this paper studies and analyzes the PROFINET protocol, Modbus protocol and PROFINET gateway technology. The ERTEC 200p chip of industrial Ethernet device series provided by Siemens is used as the main processor, and the high speed and large capacity SDRAM memory, NOR Flash memory and other interface circuits are expanded externally to form the hardware board based on ERTEC 200p. This hardware board runs e-Cos embedded real-time operating system, PROFINET protocol stack, and makes application development in the upper layer of the protocol stack. A development board based on chip STM32F103VET6 is designed, which runs the master station program of Modbus protocol on the expansion board. The expansion board provides the connection between RS-485 and industrial field equipment, and makes application and development on the expansion board. The hardware board based on ERTEC 200p and the expansion board based on STM32F103VET6 are connected by 11 GPIO channels to form the hardware of PROFINET gateway. Finally, by building a hardware and software platform, the communication between the devices embedded in Modbus protocol and the devices embedded in PROFINET protocol is debugged on-line, and the performance index of the system is tested by experiments. Test results: from the Modbus protocol to send data from the station end, the PROFINET protocol terminal can receive the corresponding data; The data is sent from the PROFINET protocol and the Modbus protocol can receive the corresponding data from the station, which has the diagnostic function. The functional development of the gateway is completed, which has a certain practical value.
【學位授予單位】：西南科技大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TN915.05

【相似文獻】

相關期刊論文 前10條

1 ;PROFInet──簡單、可靠、獨立于系統:自動化的未來[J];儀器儀表標準化與計量;2001年01期

2 楊少華;;RS485與PROFINET跨網通訊的實現[J];電氣傳動;2011年05期

3 莫太平;王丹;吳正高;;基于Profinet的電能遠程監控系統[J];自動化與儀表;2012年10期

4 ;基于網絡的PROFINET培訓——為用戶設計系統時提供支持[J];中國儀器儀表;2012年06期

5 Peter Fuchs;Knut Dettmer;;PROFINET實施方案—TPS-1芯片[J];中國儀器儀表;2014年08期

6 繆彬彬;鄧銳;;基于PROFINET工業以太網通信的稱重解決方案[J];中國儀器儀表;2014年01期

7 田民;張文焱;呂漢;;基于PROFINET的卷包除塵控制系統[J];自動化技術與應用;2013年12期

8 陸章杰;;西門子PROFINet在舞臺控制中的應用[J];中國儀器儀表;2013年S1期

9 張丹丹;;升級到工業以太網:PROFINET[J];國內外機電一體化技術;2008年05期

10 施華;喬叢;楊斌;程雪;;物流系統中基于PROFINET工業以太網的運用研究[J];制造業自動化;2013年11期

相關碩士學位論文 前2條

1 陳雷;基于PROFINET通信協議的IO設備研究[D];合肥工業大學;2016年

2 鄧正宇;基于ERTEC 200P的PROFINET工控網關的研制[D];西南科技大學;2017年

，

本文編號：2453032