【摘要】：以Pd79Cu4Au2Si10P5塊體非晶合金為對象,研究了不同尺寸合金的塑性變形行為及其內部剪切帶特征。結果表明,直徑為1,2和3 mm的該非晶合金都具有良好的塑性變形能力,其塑性變形量隨著試樣尺寸的增大而降低,分別約為13%,10%,8%。不同尺寸試樣的應力-應變曲線有明顯不同的鋸齒流變,2 mm試樣鋸齒振幅最大,3 mm試樣鋸齒振幅最小,而且1和3 mm試樣的應力-應變曲線的鋸齒間隔都比2 mm試樣的小。金相顯微鏡的觀察結果表明,隨著試樣尺寸的增加,其內部主剪切帶密度降低,次生剪切帶密度增加。在掃描電鏡下能明顯看到內部主剪切帶厚度隨著試樣尺寸的增加而增加。
[Abstract]:The plastic deformation behavior and internal shear band characteristics of Pd79Cu4Au2Si10P5 bulk amorphous alloys with different sizes were studied. The results show that the amorphous alloys with diameters of 1, 2 and 3 mm have good plastic deformation ability, and their plastic deformation decreases with the increase of sample size, which is about 13%, 10% and 8%, respectively. The stress-strain curves of samples with different sizes have obviously different sawtooth flow curves. The sawtooth amplitude of 2 mm specimen is the largest, and the sawtooth amplitude of 3 mm specimen is the smallest, and the sawtooth interval of 1 and 3 mm specimens is smaller than that of 2 mm specimen. The results of metallographic microscope show that with the increase of sample size, the density of main shear band decreases and the density of secondary shear band increases with the increase of sample size. Under scanning electron microscope, it can be seen that the thickness of the main shear band increases with the increase of sample size.
【作者單位】： 煙臺大學;
【基金】：國家自然科學基金(51101133,51101134) 山東省優秀中青年科學家科研獎勵基金(BS2012CL036) 山東省自然科學基金(ZR2011EL025)
【分類號】：TG139.8

【共引文獻】

相關期刊論文 前10條

1 董福宇;駱良順;蘇彥慶;郭景杰;傅恒志;;氫對非晶合金影響的研究進展[J];稀有金屬材料與工程;2013年07期

2 白楊;邢路闊;李相波;李焰;;海洋環境防滑涂層技術研究進展[J];腐蝕科學與防護技術;2013年06期

3 何翠群;晏建武;楊艷艷;盧全國;曹清華;;納米晶及非晶鎂基貯氫合金薄膜的研究進展[J];功能材料與器件學報;2013年06期

4 Meiting Xie;Pengna Zhang;Kaikai Song;;Thermal Stability and Transformation-mediated Deformability of Cu-Zr-Al-Ni Bulk Metallic Glass Composite[J];Journal of Materials Science & Technology;2013年09期

5 董明斌;李楨;顧及;宋e，

本文編號：2505539