【摘要】：為增強軟固結磨粒氣壓砂輪基體的耐疲勞性和抗撕裂性,提出了基于短纖維增強理論調控氣壓砂輪基體力學性能的方法.分析了芳綸漿粕(PPTA-Pulp)短纖維增強氣壓砂輪基體性能的作用機理,通過理論公式與拉伸試驗的相互驗證,得出了增強后氣壓砂輪基體的彈性模量隨短纖維添加比例增大而增大的規律;通過短纖維不同添加比例的氣壓砂輪基體褲型試樣的撕裂對比試驗,證明了短纖維增強氣壓砂輪基體在提高抗撕裂性方面的有效性;仿真分析了增強后氣壓砂輪在不同工況下接觸區域的應力分布特性,通過加工試驗,驗證了短纖維增強氣壓砂輪對高硬度、高耐磨性模具高效加工的能力.
[Abstract]:In order to enhance the fatigue resistance and tear resistance of the pneumatic abrasive wheel matrix, a method to control the mechanical properties of the pneumatic wheel matrix based on the short fiber reinforcement theory was proposed. The mechanism of aramid pulp (PPTA-Pulp) short fiber reinforced air pressure grinding wheel matrix was analyzed, and the mutual verification of theoretical formula and tensile test was carried out. The law that the elastic modulus of air pressure grinding wheel matrix increases with the increase of the proportion of short fiber after reinforcement is obtained. Through the tear test of air pressure wheel matrix with different proportion of short fiber, it is proved that short fiber reinforced air pressure wheel matrix is effective in improving tear resistance. The stress distribution characteristics of the contact region of the reinforced pneumatic grinding wheel under different working conditions are analyzed by simulation. The processing tests show that the short fiber reinforced pneumatic grinding wheel can efficiently process the mould with high hardness and high wear resistance.
【作者單位】： 浙江工業大學特種裝備制造與先進加工技術教育部/浙江省重點實驗室;
【基金】：國家自然科學基金項目(51175471,50575208,51205358) 浙江省科技廳創新團隊項目(2011R50011-07)
【分類號】：TG743

【參考文獻】

相關期刊論文 前7條

1 任超;陳建鈞;潘紅良;;纖維增強復合材料黏彈性行為的預測模型[J];復合材料學報;2012年01期

2 任超;陳建鈞;潘紅良;;隨機短纖維增強復合材料彈性模量預測模型[J];復合材料學報;2012年04期

3 張學成;戴一帆;李圣怡;;磁射流拋光中磁場的分析與設計[J];航空精密制造技術;2006年01期

4 計時鳴;金明生;張憲;張利;張銀東;袁巨龍;;應用于模具自由曲面的新型氣囊拋光技術[J];機械工程學報;2007年08期

5 張偉;李洪玉;金海;;氣囊拋光去除函數的數值仿真與試驗研究[J];機械工程學報;2009年02期

6 計時鳴;曾晰;金明生;譚大鵬;董鍵;;軟固結磨粒群加工方法及材料去除特性的分析[J];機械工程學報;2013年05期

7 何柏林;孫佳;史建平;;工模具材料激光表面強化處理應用與發展[J];熱加工工藝;2009年18期

【共引文獻】

相關期刊論文 前10條

1 陳國達;計時鳴;金明生;張才;;面向等殘余面形誤差的分層修形模具氣囊拋光軌跡規劃方法[J];兵工學報;2012年06期

2 王偉;，

本文編號：2412314