【摘要】：針對立銑加工系統的刀具子結構和刀柄子結構結合部研究了一種兩點結合導納綜合動力學模型。采用導納綜合法研究了兩點結合模型的刀尖點位移導納計算公式。利用Ansys軟件進行了刀具子結構和刀柄子結構位移導納分析,導出位移導納數據。采用Matlab軟件編寫兩點結合導納綜合法程序,獲得了刀尖點位移導納函數。通過Ansys軟件建立了刀具子結構和刀柄子結構整體有限元模型,分析獲得了刀尖點位移導納函數。與兩點結合導納綜合法分析結果進行比較,并計算兩者相對誤差,結果表明:在關注頻率范圍內相對誤差最大為0.7%,試驗結果與兩點結合導納綜合法分析結果具有很好的一致性。
[Abstract]:A two-point combined admittance comprehensive dynamic model is studied for the joint of tool substructure and cutter shank substructure in the end milling system. In this paper, the displacement admittance formula of knife tip is studied by using admittance synthesis method. The displacement admittance analysis of tool substructure and cutter shank substructure is carried out with Ansys software, and the displacement admittance data are derived. The displacement admittance function at the tip of the cutter is obtained by using the program of two points combined with the admittance synthesis method written by Matlab software. The finite element models of tool substructure and tool shank substructure are established by Ansys software, and the displacement admittance function of cutter tip is obtained. The results are compared with the results of two-point combined admittance synthesis method and the relative errors of the two methods are calculated. The results show that the maximum relative error is 0.7 in the range of frequency of concern. The experimental results are in good agreement with the results of two-point combined admittance analysis.
【作者單位】： 東北大學機械工程與自動化學院;
【基金】：國家自然科學基金項目(51105067) 教育部基本科研業務費項目(N120403011)
【分類號】：TG54

【相似文獻】

相關期刊論文 前10條

1 劉宇;張偉龍;張義民;呂春梅;;基于導納綜合法的立銑加工刀尖點動態特性預測[J];東北大學學報(自然科學版);2013年08期

2 ;[J];;年期

3 ;[J];;年期

4 ;[J];;年期

5 ;[J];;年期

6 ;[J];;年期

7 ;[J];;年期

8 ;[J];;年期

9 ;[J];;年期

10 ;[J];;年期

，

本文編號：2306901