本文選題：Inconel + 合金��； 參考：《中國有色金屬學報》2015年12期

【摘要】：采用等溫?zé)釅嚎s實驗研究DP工藝Inconel 718合金在變形溫度為900~1060℃,應變速率為0.001~0.5 s~(-1)條件下的高溫流變行為,分析摩擦因數和絕熱溫升對真應力-真應變曲線的影響,并對摩擦引起的流變應力誤差進行了修正,建立了基于應變量的應變本構模型。結果表明:隨著應變速率的增大和變形溫度的降低,摩擦因數的影響趨于明顯,變形激活能和材料常數是應變量的函數。對引入應變量參數建立的用于預測工藝處理的Inconel718合金不同變形量時的流變應力本構模型進行誤差分析,其實驗值與預測值的相關性系數為0.998,平均相對誤差絕對值為3.87%,能夠用于準確預測不同變形量時合金的流變應力值。
[Abstract]:The isothermal compression test was used to study the rheological behavior of DP Inconel 718 Alloy at a deformation temperature of 900~1060 C and the strain rate of 0.001~0.5 s~ (-1). The effect of friction factor and adiabatic temperature rise on true stress true strain curve was analyzed, and the strain error caused by friction was corrected, and the strain based on strain was established. The results show that with the increase of the strain rate and the decrease of the deformation temperature, the influence of the friction factor tends to be obvious, the deformation activation energy and the material constant are the function of the strain. The rheological stress constitutive model for the different deformation quantity of Inconel718 gold which is used to predict the process treatment is established. In the error analysis, the correlation coefficient between the actual and the predicted values is 0.998, the absolute value of the average relative error is 3.87%, and it can be used to accurately predict the rheological stress values of the alloys with different deformation quantities.
【作者單位】： 中南林業科技大學機電工程學院;中南大學粉末冶金國家重點實驗室;
【基金】：國家高技術研究發展計劃資助項目(2012AA03A514) 國家自然科學基金資助項目(51401242,51301209,61271356,51205031)
【分類號】：TG146.15

【共引文獻】

相關期刊論文 前10條

1 司家勇;劉鋒;;δ相對Inconel 718合金組織與疲勞性能影響的研究進展[J];材料導報;2013年07期

2 李卿;郭鴻鎮;王彥偉;趙張龍;姚澤坤;;GH4049合金的熱變形行為及組織演變[J];材料工程;2014年12期

3 董洪波;王高潮;;變形工藝對Inconel718合金超塑性的影響(英文)[J];稀有金屬材料與工程;2015年02期

4 郝用興;楊松偉;郭華毅;張勇;;臺階軸胎模鍛填充不滿機理分析與對策研究[J];華北水利水電學院學報;2012年05期

5 高鵬;張凱鋒;蔣少松;;漸變曲率Inconel718厚板熱彎曲成形精度與表面質量控制[J];航空材料學報;2012年06期

6 田素貴;王欣;謝君;劉臣;郭忠革;劉姣;孫文儒;;GH4169G合金熱處理期間的相轉變特征與機理分析[J];金屬學報;2013年07期

7 楊長勇;徐九華;顧s舠，

本文編號：2086378