本文選題：FGC斷帶 + 軋輥毛化粗糙度�。� 參考：《遼寧科技大學》2015年碩士論文

【摘要】：本文以冷軋UCM軋機FGC斷帶和末機架軋輥粗糙度均勻性為研究對象,通過實踐與理論分析完成冷軋UCM軋機生產穩定性的相關研究。針對酸軋F(tuán)GC斷帶,主要通過對電氣二級程序中FGC過渡軋制表優化和在一級和二級程序中將剪切時序提前以及針對特定鋼種做自動抬輥縫功能,最終通過統計學的方法,將容易發生斷帶的鋼種進行預判,增加合理過渡料降低斷帶風險。末架軋輥粗糙度均勻性研究,主要利用minitab軟件進行,對所有影響因素進行分析,由FMEA打分,篩選因素,隨后進行DOE設計實驗,找出主要影響因素,運用相應曲面找到合理打毛參數配比,最終確定的毛化工藝參數為橫移速度為45mm/min、通電時間為17us、斷電時間為41us,達到Ra為3.6um±0.15的軋輥粗糙度合格率在80%以上。
[Abstract]:In this paper, the coarseness uniformity of cold UCM rolling mill FGC break and end stand roll is taken as the research object, and the production stability of cold UCM mill is studied by practical and theoretical analysis. In view of acid rolling FGC break strip, by optimizing the FGC transition rolling table in the electrical secondary program, advancing the shearing timing in the first and second grade programs, and making automatic lifting roll gap function for specific steel grades, the final statistical method is adopted. In order to increase the reasonable transition material and reduce the risk of broken zone, the steel grade which is prone to break zone is forecasted. The research on the roughness uniformity of the final roller is mainly carried out by using minitab software. All the influencing factors are analyzed, and the factors are scored by FMEA and screened. Then, the design experiment of DOE is carried out to find out the main influencing factors. Using the corresponding surface to find out the reasonable ratio of tapping parameters, the final process parameters are 45 mm / min traverse speed, 17 us. electrification time and 41 us. the qualified rate of roughness of roller with Ra being 3.6um 鹵0. 15 is over 80%.
【學位授予單位】：遼寧科技大學
【學位級別】：碩士
【學位授予年份】：2015
【分類號】：TG333

【參考文獻】

相關期刊論文 前2條

1 傅作寶;;冷軋薄板和冷軋帶鋼生產技術的發展(二)[J];鞍鋼技術;1980年09期

2 宋加;縱談我國冷軋板生產[J];軋鋼;2001年04期

，

本文編號：1865599