發布時間：2018-04-11 08:00

  本文選題：內高壓成形 + 位置同步控制�。� 參考：《機床與液壓》2015年23期

【摘要】：內高壓成形過程中兩側缸位置同步控制問題,是內高壓成形控制系統的關鍵技術之一。應用自主研制的多變量協調控制模擬試驗平臺進行仿真與試驗研究,對側缸位置控制系統建立數學模型,采用"同等+主從"控制方式,利用Simulink搭建該系統的PID控制仿真模型進行仿真,仿真結果證明了采用PID控制進行試驗的可行性。在此基礎上采用S7-300 PLC作為主控制器,基于Win CC組態軟件,進行單側缸位置PID控制及兩側缸位置同步PID控制試驗研究,試驗結果表明:基于S7-300 PLC的兩側缸位置同步PID控制系統,同步控制精度高、抗干擾能力強,能夠滿足內高壓成形機位置同步系統控制要求,為S7-300 PLC在內高壓成形機控制系統上的實際應用提供了參考。
[Abstract]:One of the key technologies of the internal high pressure forming control system is the simultaneous control of the position of the two sides of the cylinder in the process of internal high pressure forming.The simulation and experimental research is carried out on the multi-variable coordinated control simulation test platform developed by ourselves. The mathematical model of the side cylinder position control system is established, and the "equal master-slave" control mode is adopted.The PID control simulation model of the system is built by using Simulink. The simulation results prove the feasibility of using PID control to carry out the experiment.On this basis, the S7-300 PLC is used as the main controller and the Win CC configuration software is used to carry out the experimental research on the single-side cylinder position PID control and the two-side cylinder position synchronization PID control system. The experimental results show that the PID control system for the two sides cylinder position synchronization is based on S7-300 PLC.The synchronous control accuracy is high and the anti-interference ability is strong. It can meet the control requirements of the position synchronization system of the internal high-pressure forming machine. It provides a reference for the practical application of the S7-300 PLC internal high-voltage forming machine control system.
【作者單位】： 燕山大學工業計算機控制工程河北省重點實驗室;滄州師范學院機械與電氣工程學院;
【分類號】：TG306

【參考文獻】

相關期刊論文 前2條

1 韓波,王慶豐,路甬祥;電液比例位置同步控制系統的控制結構研究[J];機床與液壓;1997年01期

2 苑世劍,王仲仁;內高壓成形的應用進展[J];中國機械工程;2002年09期

相關碩士學位論文 前1條

1 陳烙，

本文編號：1735115