【摘要】：目的提升鈦合金(TC4)葉片表面性能,解決失效問題。方法實驗采用激光局部氣體氮化工藝代替?zhèn)鹘y(tǒng)氮化工藝,利用2 k W柔性光纖耦合半導體激光器在鈦合金(TC4)基體表面采用氣體氮化的方法制備TiN表面改性層。采用摩擦磨損試驗機和改制的汽蝕裝置分別測試了氮化層與基體(TC4)的耐磨性與抗汽蝕性能。結果摩擦磨損實驗后,激光氮化層的質量損失為2.3 mg,基體TC4的質量損失為20.2 mg,激光氮化層的損失質量為基體TC4的11.3%,激光氮化層抗磨損性能相較基體TC4提高了7倍。TC4基體汽蝕損失的質量為4.08 mg,而氮化層的質量損失為1.13 mg,氮化層的抗汽蝕性能比基體提高了2.61倍。結論采用半導體激光氣體氮化鈦合金葉片能夠得到分布著大量TiN枝晶的氮化層,提高表面耐磨損性能,氮化層中的TiN枝晶構成的網籃狀組織對其表面抗汽蝕性能也有所提高。
[Abstract]:Objective to improve the surface properties of titanium alloy (TC4) blades and solve the failure problem. Methods the laser partial gas nitridation process was used to replace the traditional nitriding process. The surface modification layer of TiN was prepared by gas nitriding on the substrate of titanium alloy (TC4) using a 2 kW flexible fiber coupled semiconductor laser. The wear resistance and cavitation corrosion resistance of nitride layer and substrate (TC4) were measured by friction and wear tester and modified cavitation device respectively. Results after friction and wear experiments, the mass loss of laser nitrided layer was 2.3 mg, substrate TC4 loss was 20.2 mg, laser nitrided layer mass loss was 11.3% of substrate TC4. The wear resistance of the laser nitrided layer is 7 times higher than that of the substrate TC4. The mass loss of the TC4 matrix is 4.08 mg, and the mass loss of the nitride layer is 1.13 mg,. The cavitation corrosion resistance of the nitrided layer is 2.61 times higher than that of the substrate. Conclusion A large number of nitride layers with TiN dendrites can be obtained by using semiconductor laser gas titanium nitride alloy blades to improve the wear resistance of the surface, and the surface cavitation corrosion resistance of the TiN dendrites in the nitride layer is also improved.
【作者單位】： 中原工學院機電學院;博雷(中國)控制系統有限公司;浙江工業大學激光先進制造研究院;浙江省高端激光制造裝備協同創新中心;浙江大學現代制造工程研究所;
【基金】：鄭州市科技計劃項目(20150483) 河南省高等學校重點科研項目(15A460038) 中國紡織工業聯合會科技指導性項目計劃(2016085)~~
【分類號】：TG178

【相似文獻】

相關期刊論文 前10條

1 陳漢清;;磁場氮化法[J];機械工人;1979年04期

2 楊天國;;談?wù)剼怏w氮化的質量與操作[J];機械工人(熱加工);1979年10期

3 胡義祥;氮化層的斷裂力學分析[J];金屬學報;1980年04期

4 J.Zysk;田金莉;;氮化層的分類和評定[J];國外化學熱處理;1981年02期

5 И.б.РодичевА;蔡人欽;;預先熱處理對無鋁結構鋼氮化層性能的影響[J];國外化學熱處理;1981年04期

6 許大慶,趙建生;幾種工業用鋼的氮化層脆性測試[J];鋼鐵研究學報;1999年01期

7 李繼良,毛U，

本文編號：2383263