【摘要】：對工業純鋁1060板料進行單點增量成形極限實驗研究,比較了圓錐形件各部位厚度的分布情況。實驗發現,當成形角增大時,成形件上部會出現厚度嚴重變薄的減薄帶,并且破裂容易出現在減薄帶上,影響板料成形極限。用最大成形角表征單點增量成形過程中的成形極限,分析了不同參數對板料最大成形角的-影響,發現層間距會影響板料的最大成形角,而工具頭周向進給速度對最大成形角的影響不大,不同形狀的成形件其最大成形角也不相同。最后通過實驗獲得了1 mm厚度鋁板的成形極限曲線(FLC)。
[Abstract]:A single point incremental forming limit experiment was carried out on industrial pure aluminum 1060 sheet metal, and the distribution of the thickness of each part of the conical part was compared. The experimental results show that when the forming angle increases, the thickness of the upper part of the forming part will be thinned seriously, and the fracture will easily appear in the thinning zone, which will affect the forming limit of sheet metal. The maximum forming angle is used to characterize the forming limit in the process of single point incremental forming. The influence of different parameters on the maximum forming angle of sheet metal is analyzed. It is found that the interval between layers will affect the maximum forming angle of sheet metal. However, the circumferential feed velocity of the tool head has little effect on the maximum forming angle, and the maximum forming angle is also different for different shapes of forming parts. Finally, the forming limit curve (FLC).) of 1 mm thick aluminum plate is obtained by experiment.
【作者單位】： 西安理工大學機械與精密儀器工程學院;
【基金】：國家自然科學基金項目(51475366) 高等學校博士學科點專項科研基金項目(20116118110005) 陜西省教育廳重點實驗室科學研究計劃項目(12JS072) 西安理工大學博士創新基金項目(2007-002J1302)資助
【分類號】：TG386

【相似文獻】

相關期刊論文 前10條

1 張樹艷;馬敘;王志華;楊繼宏;楊全祿;呂麗莎;劉遠鋒;;冷軋深沖板應力成形極限的研究[J];重型機械;2013年02期

2 周亮 ,陳鶴崢;根據穩定理論建立的理論成形極限曲線[J];北京航空學院學報;1986年01期

3 林大為,屠挺生,戴一一,張順才;板料真實成形極限的測定及其應用[J];鍛壓技術;2001年03期

4 李立軍,祝洪川;薄鋼板成形極限曲線的研究[J];物理測試;2003年05期

5 陳R際，

本文編號：2162988