本文選題：脈沖電鍍 + Ni-Cr-Mn合金鍍層��； 參考：《熱加工工藝》2017年18期

【摘要】：利用脈沖電鍍方法在Q235鋼表面制備N(xiāo)i-Cr-Mn合金鍍層。采用輝光放電光譜儀、電化學工作站等設備,研究了不同的配位劑:甲酸銨、檸檬酸銨、復合配位劑A對Ni-Cr-Mn合金鍍層成分、沉積速率及耐蝕性的影響。結果表明,三種不同的配位劑對Ni-Cr-Mn合金鍍層成分、沉積速率及耐蝕性的影響相同。隨著配位劑含量的增加,鍍層中Cr、Mn含量先升高后降低,Ni含量先降低后升高;然而沉積速率先升后降;復合配位劑A制備的Ni-Cr-Mn合金鍍層,具有最小的腐蝕電流密度、最大的腐蝕電位,分別為9.374×10~(-8)A/cm~2、-0.288 V,耐蝕性更佳。
[Abstract]:Ni-Cr-Mn alloy coating was prepared on the surface of Q235 steel by pulse electroplating. The effects of different coordination agents, such as ammonium formate, ammonium citrate and complex coordination agent A, on the composition, deposition rate and corrosion resistance of Ni-Cr-Mn alloy coating were studied by means of glow discharge spectrometer and electrochemical workstation. The results show that the effect of three different coordination agents on the composition, deposition rate and corrosion resistance of Ni-Cr-Mn alloy coating is the same. With the increase of the content of coordination agent, the content of Cr-Mn in the coating increased first, then decreased and then increased, but the deposition rate increased first and then decreased. The Ni-Cr-Mn alloy coating prepared by complex coordination agent A had the smallest corrosion current density. The maximum corrosion potential is 9.374 脳 10 ~ (-8) A / cm ~ (-2) -0.288 V, and the corrosion resistance is better.
【作者單位】： 華北理工大學冶金與能源學院現代冶金技術教育部重點實驗室;
【基金】：國家自然科學基金資助項目(51474088)
【分類號】：TQ153

【相似文獻】

相關期刊論文 前10條

1 張玉峰;吳嘵明;吳剛;;兩種配位劑對刷鍍鎳-磷合金協同效應的分析[J];電鍍與環保;2008年06期

2 杜朝軍;劉建連;謝英男;喻國敏;;以蛋氨酸為配位劑的無氰鍍銀工藝研究[J];電鍍與環保;2011年01期

3 畢四富;龔超;屠振密;李寧;;配位劑對低濃度硫酸鉻鍍鉻的影響[J];電鍍與精飾;2011年09期

4 朱焱;江茜;張印;李鵬;;化學鍍鎳磷合金復合配位劑的研究[J];電鍍與涂飾;2013年03期

5 賴奐汶;丁汀;黃清安;;無氰堿性鋅鎳合金電鍍中配位劑的選擇[J];電鍍與涂飾;2008年01期

6 譚利華;葉福東;魏U喠，

本文編號：2017636