【摘要】：柔性直流輸電換流閥屏蔽系統的表面電場計算與屏蔽效果分析對閥塔均壓環設計與表面場強控制具有重要作用,本文使用伽遼金間接邊界元方法首先對理想化模型屏蔽系統的屏蔽效果進行研究,構建理想化屏蔽系統模型并分別對未加均壓環的閥箱體結構與施加均壓環的整體結構進行表面場強計算,具體分析了均壓環的高度、位置、間距對閥箱體結構表面場強的影響,獲得了一定的規律；進一步對不同的均壓環設計方案進行比較,在滿足約束條件下根據比較結果總結了合適方案,施加合適方案下的均壓環使閥箱體得到良好屏蔽且均壓環無起暈現象。比較結果說明換流閥體結構外部均壓環之間距離越大,閥箱體結構所對應的棱邊中點場強越大,均壓環的施加使閥箱體模型對應尖角部位表面場強大幅度減小且均壓環高度越大,閥箱體尖角部位表面場強越小。本文對實際工程中換流閥屏蔽系統的屏蔽效果進行詳細地研究,針對工程中的絕緣要求分析改變均壓環的尺寸、間距等參數后是否滿足屏蔽要求；進一步在絕緣設計過程中調整屏蔽系統結構,提出了考慮閥體模塊、橫板立柱、法蘭以及球等結構的計算模型,使計算更加準確,計算結果表明實際工程中法蘭表面場強不可忽略,側面應做成光滑曲面。根據電壓施加方式,對實際閥塔結構分成不同時刻不同情況建立考慮較為全面的計算模型,詳細介紹了每種情況下的建模方式、原理、電壓施加方式并計算閥塔結構中關鍵部位的表面電場,總結了規律并驗證了實際工程中屏蔽系統的絕緣可行性,解決了工程中的絕緣設計問題。
[Abstract]:The calculation of the surface electric field and the analysis of the shielding effect of the flexible HVDC converter valve shield system play an important role in the design of the valve tower pressure sharing ring and the control of the surface field intensity. In this paper, Galerkin indirect boundary element method is used to study the shielding effect of the idealized model shielding system. The idealized shielding system model is constructed and the surface field strength of the valve box structure without the uniform pressure ring and the whole structure with the uniform pressure ring applied are calculated respectively. The influence of the height, position and spacing of the uniform pressure ring on the surface field intensity of the valve box structure is analyzed in detail. A certain rule is obtained. Furthermore, the different design schemes of the equalizing ring are compared. According to the comparison results, the suitable scheme is summarized under the constraint condition. The pressure sharing ring under the suitable scheme can make the valve box get good shielding and there is no halo phenomenon in the equalizing pressure ring. The comparison results show that the greater the distance between the outer pressure rings of the commutation valve body is, the greater the field intensity of the center point corresponding to the valve box structure is. The application of the uniform pressure ring reduces the strong amplitude of the surface field of the valve box corresponding to the sharp angle and the greater the height of the uniform pressure ring, the smaller the surface field intensity of the valve box is. In this paper, the shielding effect of commutation valve shielding system in practical engineering is studied in detail. According to the insulation requirements in engineering, whether the parameters such as the size and spacing of the pressure sharing ring can meet the shielding requirements are analyzed. Furthermore, the structure of shield system is adjusted in the process of insulation design, and a calculation model considering the structure of valve body module, transverse plate column, flange and ball is put forward to make the calculation more accurate. The calculation results show that the flange surface field strength can not be ignored and the flange surface should be made into a smooth surface. According to the way of applied voltage, the calculation model of the actual valve tower structure is established and considered in different time and different situation, and the modeling method and principle of each case are introduced in detail. The voltage applied mode and the surface electric field of the key part of the valve tower structure are calculated, the regularity is summarized and the insulation feasibility of the shield system in the actual engineering is verified, and the insulation design problem in the engineering is solved.
【學位授予單位】：華北電力大學(北京)
【學位級別】：碩士
【學位授予年份】：2014
【分類號】：TM721.1

【參考文獻】

相關期刊論文 前10條

1 劉士利;王澤忠;孫超;;應用伽遼金邊界元法的直流換流站屏蔽罩表面場強計算[J];電網技術;2011年05期

2 田冀煥;周遠翔;郭紹偉;聶瓊;孫清華;梁曦東;;直流換流站閥廳內三維電場的分布式并行計算[J];高電壓技術;2010年05期

3 張燕秉;鄭勁;汪德華;李文平;;特高壓直流換流變壓器的研制[J];高電壓技術;2010年01期

4 劉兵;阮江軍;韓海宏;余世峰;吳田;;柔性直流輸電系統電磁環境分析[J];高電壓技術;2009年11期

5 鄧桃;李慶峰;張學軍;宿志一;范建斌;;±800kV特高壓直流線路均壓環優化研究(英文)[J];中國電機工程學報;2009年22期

6 馬為民;聶定珍;萬保權;張小武;謝輝春;李妮;;高壓直流換流站閥廳屏蔽效能的研究[J];高電壓技術;2008年11期

7 陳慶國;張杰;高源;魏新勞;;混合電場作用下?lián)Q流變壓器閥側繞組電場分析[J];高電壓技術;2008年03期

8 王澤忠;李亞莎;鄧春華;;基于球坐標的三維靜電場曲邊四邊形邊界元方法[J];電工技術學報;2007年04期

9 王建民;張喜樂;吳增泊;孫優良;趙文祥;;高壓直流換流變壓器電磁場特性的數值應用研究[J];變壓器;2007年03期

10 李亞莎;王澤忠;;基于柱坐標的三維靜電場曲邊四邊形邊界元法[J];高電壓技術;2007年01期

相關博士學位論文 前4條

1 劉士利;改進的邊界元法及其在電場計算中的應用[D];華北電力大學（北京）;2011年

2 陳澤軍;三維彈性接觸Taylor級數多極邊界元法理論與應用研究[D];燕山大學;2009年

3 李亞莎;高精度快速邊界元法及其在絕緣子電場計算中應用研究[D];華北電力大學（北京）;2007年

4 周平;電磁散射問題中有限元法和邊界元法及其混合技術研究[D];南京航空航天大學;2006年

相關碩士學位論文 前2條

1 武坤;特高壓直流線路復合絕緣子均壓環優化研究[D];重慶大學;2008年

2 劉姜玲;合成絕緣子三維電場分區邊界元法的研究[D];華北電力大學（北京）;2003年

，

本文編號：2340504