本文選題：刀間距 + 貫入度��； 參考：《沈陽建筑大學學報(自然科學版)》2017年05期

【摘要】：目的研究滾刀破巖過程中,貫入度與滾刀所受平均滾動力之間的相應關系,分析刀間距、貫入度以及線速度三因素對比能的影響.方法利用ABAQUS有限元仿真軟件,建立雙滾刀直線切割大理巖的運動模型,模擬5種不同貫入度的滾刀破巖過程,得出不同貫入度條件下滾刀所受平均滾動力的大小;基于正交試驗法,選出具有代表性的三因素三水平的參數組合進行仿真,通過極差分析找出不同因素變化對比能的影響規律.結果貫入度由4 mm增加到8 mm,滾刀所受平均滾動力近似線性增長,變化平緩;貫入度由8 mm增加到12 mm,滾刀所受平均滾動力增長幅度大,變化明顯.正交試驗中,刀間距對比能的均值極差為0.96 MJ/m~3;貫入度對比能的均值極差為0.41 MJ/m~3;線速度對比能的均值極差為0.26 MJ/m~3.結論在刀間距和線速度保持不變的條件下,滾刀所受平均滾動力與貫入度呈正比,而與s/p比值呈反比.通過分析刀間距、貫入度以及線速度變化對比能影響的主次性,得出刀間距影響最大,其次是貫入度,線速度影響最小.研究結果為提高滾刀破巖效率提供了參考.
[Abstract]:Aim to study the relationship between the penetration and the average rolling force of the hob during the rock breaking process of the hob, and analyze the influence of three factors on the comparison energy between the blade spacing, the penetration degree and the line velocity. Method the ABAQUS finite element simulation software is used to establish the model of the double hob straight line cutting marble, and simulate the rock breaking of the 5 kinds of hob with different penetration. According to the orthogonal test method, the parameters combination of three factors and three levels is simulated, and the influence law of the contrast energy of different factors is found through the difference analysis. The results of the result are increased from 4 mm to 8 mm, and the average rolling force of the hob is approximate. Linear growth, the change is gentle, the penetration is increased from 8 mm to 12 mm, the average rolling force of the hob increases greatly and the change is obvious. In the orthogonal test, the mean difference of the contrast energy is 0.96 MJ/m~3, the mean difference of the contrast energy is 0.41 MJ/m~3, the mean difference of the line velocity comparison energy is 0.26 MJ/m~3. conclusion in the distance and line of the knife. Under the condition of constant speed, the average rolling force and penetration of the hob are in direct proportion to the s/p ratio, and the ratio is inversely proportional to the ratio of the tool spacing, penetration and line velocity. The tool spacing has the greatest influence, followed by the penetration degree, and the linear velocity has the smallest influence. The research results can provide the improvement of the rock breaking efficiency of the hob. The reference.

【作者單位】： 沈陽建筑大學機械工程學院;沈陽建筑大學計劃財務處;北方重工集團有限公司;
【基金】：國家十二五科技支撐計劃項目(2011BAJ02B07) 教育部創新團隊支持計劃項目(IRT-15R45) 住房和城鄉建設部項目(2015-K3-006) 沈陽市科技局項目(F16-205-1-15) 遼寧省科技廳項目(2015020149) 遼寧省教育廳項目(LJZ2016020)
【分類號】：U455.3

【相似文獻】

相關期刊論文 前6條

1 王炳煌;打樁公式和貫入度[J];水運工程;1989年04期

2 王晉;;基于變形協調原則的打樁控制貫入度計算[J];水運工程;2006年S1期

3 柴長清;;打樁過程中貫入度的突變異常問題(續)[J];港口工程;1989年02期

4 朱榮太;單仁付;;打入樁“標高控制為主、貫入度為輔”原則的探討[J];科技創新導報;2010年17期

5 王召遷;王吉業;張志敏;關振華;;盤形滾刀破巖力影響因素試驗研究[J];東北大學學報(自然科學版);2014年07期

6 李俊;;TBM的原理和效能預測[J];水電站設計;2010年01期

，

本文編號：1849508