本文選題：可見光通信　切入點：光源布局　出處：《紅外與激光工程》2017年11期

【摘要】：在可見光通信系統中,光源具有照明和通信的雙重作用,由于房間的大小以及室內環境各不相同,難免會存在光照射不到或者光線比較微弱的地方,這些地方很有可能成為通信的盲區,這將會大大影響通信的質量,為了解決陰影效應,需合理對光源進行布局設計,以4 m×4 m×3 m房間為模型,采用四個LED列陣作為室內光源,將單個的LED光源看做朗伯光源,服從朗伯輻射模型,通過公式計算結合軟件仿真分析對比得出了采用9×9大小的LED列陣,列陣距離屋頂邊緣0.4 m,LED光源間的間距為0.03 m時,在滿足國際室內照明標準的前提下,在距離屋頂2.25 m的4 m×4 m接收平面上光照度分布最均勻,其均勻度達到90.4%。該光源列陣布局模型可推廣到任意尺寸房間,為室內辦公照明中光源的布局提供了一種可行的方案。
[Abstract]:In the visible light communication system, the light source has the dual function of lighting and communication. Because the room size and indoor environment are different, it is inevitable that there are places where the light can not be illuminated or the light is weak.These places are likely to be the blind areas of communication, which will greatly affect the quality of communication. In order to solve the shadow effect, it is necessary to reasonably design the light source, taking 4 m 脳 4 m 脳 3 m room as the model and using four LED arrays as the indoor light source.Taking a single LED source as a Lambert light source and applying the Lambert radiation model, a 9 脳 9 size LED array with a spacing of 0.03 m from the edge of the roof is obtained by formula calculation and software simulation analysis.On the premise of meeting the international indoor lighting standard, the light intensity distribution is the most uniform on the receiving plane of 4 m 脳 4 m from the roof 2.25 m, and the uniformity reaches 90.4%.The light source array layout model can be extended to any size room, which provides a feasible scheme for the layout of light source in indoor office lighting.
【作者單位】： 西安工業大學電子信息工程學院;
【基金】：國家自然科學基金(61271362) 陜西省科技廳一般項目-工業領域(2017GY-081) 陜西省自然科學基金(2017JM6041) 西安市科技計劃項目(2017075CG/RC038(XAGY0012)) 陜西省教育廳科技專項(2017JK0373)
【分類號】：TN929.1

【相似文獻】

相關期刊論文 前1條

1 丁德強;柯熙政;李建勛;;VLC系統的光源布局設計與仿真研究[J];光電工程;2007年01期

，

本文編號：1700732