【摘要】：壓電泵可通過電信號精確控制流體輸出,并且體積小,能耗低,無電磁干擾,工作噪聲低,在生物醫療、化學分析、芯片冷卻、噴墨打印等方面具有廣闊前景,是目前微流體領域研究的熱門課題。目前研究人員在壓電泵結構方面進行了深入具體的研究,而在壓電泵驅動、控制方面的研究相對較少,無法充分發揮出壓電泵在流體輸送精密控制方面的優勢,因此對該方面進行研究顯得十分迫切。本文結合教育部高等學�？蒲袆�(chuàng)新重大培育資金項目及國家自然科學基金項目,圍繞單雙相壓電泵系統,開展了結構設計、專用驅動電源研制、輸出性能測試、流量自測量及液體輸送精密控制方面的工作。 1.泵用壓電振子性能分析及測試 壓電振子是單雙相壓電泵核心驅動部件,利用Butterworth Van Dyke等效電路模型,分析直徑為35mm的泵用雙晶片壓電振子阻抗特性,對壓電振子阻抗特性進行測試,找出壓電振子一階共振頻率,并計算出對應的阻抗模；對圓形雙晶片壓電振子變形能力進行試驗研究,分別測試壓電振子表面各點變形位移,壓電振子中心位移與驅動電壓、驅動頻率的關系,為壓電泵的結構設計及驅動電路設計奠定基礎。 2.單雙相壓電泵的設計研制 分析單、雙相壓電泵,包括單腔單振子壓電泵、雙腔串聯壓電泵、雙腔并聯壓電泵、主被動閥結合泵、雙主動閥壓電泵的工作原理,推導單腔單振子壓電泵輸出能力與壓電振子結構參數、材料性能參數、驅動信號參數間關系,分析主動閥結構參數對工作性能的影響。分析表明與單腔單振子壓電泵相比,雙腔串聯壓電泵具有更大的輸出壓力,雙腔并聯泵具有更大的輸出流量；對雙腔串聯壓電泵、雙腔并聯壓電泵來說,異步驅動方式比同步驅動方式具有更好的輸出性能；雙主動閥壓電泵中具有更寬的工作頻率范圍,并可實現液體雙向輸送,具有獨特的輸出性能。制作單雙相壓電泵樣機,為驅動控制的研究提供載體。 3.壓電泵專用驅動電源研制 在對壓電泵驅動信號分析基礎上,以單雙相壓電泵為驅動對象,研制三種專用驅動電源：模擬式單相壓電泵驅動電源、程控式單相壓電泵驅動電源及數字控制式雙相壓電泵驅動電源。分析驅動電源系統及各部分電路工作機理。對研制的壓電泵驅動電路電氣輸出性能進行測試。 研制的三種驅動電源,輸出電壓均可在0V到最大值之間調節,最大輸出電壓不小于170V；輸出頻率可在5Hz-500Hz之間調節,其中模擬式單相壓電泵驅動電源體積小、成本低廉。程控式單相壓電泵驅動電源可通過按鍵對輸出參數調節,避免電位器接觸不良帶來的影響,提高了電源信號輸出的可靠性及穩定性；數字控制式雙相壓電泵驅動電源利用直接數字式頻率合成技術,可輸出兩列有嚴格相位關系的正弦信號,相位差可在00-360。范圍內調節,相位差最小分辨率為11.25。,采用數字化控制,輸出參數實時顯示。研制的三種驅動電源輸出參數能夠獨立、連續調節,可以靈活方便地對壓電泵進行驅動控制。 4.單雙相壓電泵輸出性能試驗研究 利用研制的數字控制式雙相壓電泵驅動電源,對單雙相信號驅動的壓電泵輸出性能進行試驗研究,研究泵輸出流量、輸出壓力與驅動電壓、驅動頻率、相位差之間的關系。可知對于雙腔串聯泵,異步驅動比同步驅動具有更好的頻率適應性及更大的輸出流量,工作頻率范圍為10Hz-400Hz,最大輸出流量為94.174mL/min,并且輸出壓力變動幅度小。對于雙腔并聯壓電泵,異步驅動方式下具有更好的輸出性能。雙主動閥壓電泵具有較寬的工作頻率范圍,從10Hz到220Hz,通過改變驅動信號間的相位差,可改變液體的流動方向及流量大小,與本文研制的其它壓電泵相比,具有獨特輸出性能。 5.基于壓電自感知的單腔單振子壓電泵流量自測量方法 提出一種利用壓電自感知功能的壓電泵流量自測量方法。對流量影響因素及傳感壓電信號與壓電振子變形關系進行分析,得出傳感壓電信號特征參數與泵流量有明確對應關系,在傳感壓電信號中隱含著壓電泵流量信息。研制用于流量自測量的傳感壓電信號參數測量電路樣機,并構造用于壓電泵流量預測的BP神經網絡模型,該神經網絡以電壓參量、頻率作為輸入?yún)?shù),得到流量的預測值。 對提出的流量自測量方法進行試驗驗證,結果表明預測值與試驗測量值之間的相關系數在0.9993以上,最大相對誤差率小于3.46%。該流量自測量方法具有較好的準確性。并且該流量自測量方法還可以應用到其它類型、結構的壓電泵中。 6.基于定脈沖數的液體輸送精密控制方法 在對壓電泵驅動特點及輸出性能分析基礎上,進行基于定脈沖數的液體精密輸送控制方法研究。研制定脈沖數控制電路,對基于定脈沖數的液體輸送精密控制方法進行試驗驗證。試驗結果表明,在不同的脈沖數下,壓電泵輸送液體體積具有良好的線性比例關系,最大相對誤差為0.424%,相關系數為0.9999,表明基于定脈沖數的液體輸送精密控制方法具有可行性。因此在流體輸送量精度要求較高的場合,可以根據輸送體積,求出對應的脈沖數,向壓電泵發送脈沖,實現流體的精密輸送控制。
[Abstract]:Piezoelectric pumps can accurately control the output of fluids through electrical signals, and have small volume, low energy consumption, no electromagnetic interference, low noise. They have broad prospects in biomedical, chemical analysis, chip cooling, inkjet printing and so on. They are hot topics in the field of microfluids. At present, researchers have conducted in-depth study on the structure of piezoelectric pumps. In this paper, the research on the piezoelectric pump drive and control is relatively small, which can not give full play to the advantages of the piezoelectric pump in the precise control of fluid delivery. Therefore, it is very urgent to study this aspect. Structural design, development of special driving power supply, output performance test, flow self-measurement and precise control of liquid conveying have been carried out.
Performance analysis and test of 1. piezoelectric vibrator for pump
Piezoelectric oscillator is the core driving component of single-phase and dual-phase piezoelectric pump. Using Butterworth Van Dyke equivalent circuit model, the impedance characteristics of bimorph piezoelectric oscillator for pump with a diameter of 35 mm are analyzed. The impedance characteristics of bimorph piezoelectric oscillator are tested. The first-order resonance frequency of the piezoelectric oscillator is found and the corresponding impedance modes are calculated. The deformation ability of the piezoelectric oscillator is tested by experiment. The relationship between the displacement of the center of the piezoelectric oscillator and the driving voltage and the driving frequency is tested, which lays a foundation for the structure design and the driving circuit design of the piezoelectric pump.
Design and development of 2. single phase dual phase piezoelectric pump
The working principle of single-cavity piezoelectric pump and dual-phase piezoelectric pump including single-cavity single-oscillator piezoelectric pump, double-cavity series piezoelectric pump, double-cavity parallel piezoelectric pump, active-passive valve combination pump and dual-active valve piezoelectric pump is analyzed. The relationship between output capacity of single-cavity single-oscillator piezoelectric pump and structural parameters of piezoelectric oscillator, material performance parameters and driving signal parameters is deduced. The analysis shows that the output pressure of the double-cavity piezoelectric pump is higher than that of the single-cavity single-oscillator piezoelectric pump, and the output flow of the double-cavity parallel pump is larger. The valve piezoelectric pump has a wider working frequency range and can realize liquid two-way transmission. It has a unique output performance.
Development of special driving power supply for 3. piezoelectric pump
Based on the analysis of driving signal of piezoelectric pump, three kinds of special driving power supply are developed, which are analog single-phase piezoelectric pump driving power supply, program-controlled single-phase piezoelectric pump driving power supply and digital control dual-phase piezoelectric pump driving power supply. The electrical output performance of the piezoelectric pump driving circuit is tested.
The output voltage of the three kinds of driving power supply can be adjusted from 0V to the maximum value, the maximum output voltage is not less than 170V, and the output frequency can be adjusted between 5Hz and 500Hz. Among them, the analog single-phase piezoelectric pump driving power supply is small in size and low in cost. The reliability and stability of the power supply signal are improved by the bad contact of the positioner. The driving power supply of the digital controlled dual-phase piezoelectric pump can output two series of sinusoidal signals with strict phase relationship by using the direct digital frequency synthesis technology. The phase difference can be adjusted in the range of 100-360. The minimum resolution of the phase difference is 11.25. With digital control and real-time display of output parameters, the output parameters of the three driving power supply can be adjusted independently and continuously, and the piezoelectric pump can be driven and controlled flexibly and conveniently.
Experimental study on output performance of 4. single phase biphase piezoelectric pump
The output performance of piezoelectric pump driven by single-phase and double-phase signals is studied experimentally by using the developed digital control driving power supply of dual-phase piezoelectric pump. The relationship between output flow, output pressure and driving voltage, driving frequency and phase difference is studied. And larger output flow, operating frequency range from 10Hz to 400Hz, the maximum output flow rate is 94.174mL/min, and the output pressure variation is small. Compared with other piezoelectric pumps developed in this paper, it has unique output performance.
5. self sensing method based on piezoelectric self sensing method for single chamber single oscillator piezoelectric pump flow measurement
A flow self-measurement method of piezoelectric pump based on piezoelectric self-sensing function is proposed. The flow influencing factors and the relationship between sensing piezoelectric signal and deformation of piezoelectric oscillator are analyzed. It is concluded that the characteristic parameters of sensing piezoelectric signal correspond to pump flow clearly. The flow information of piezoelectric pump is hidden in sensing piezoelectric signal. The self-measured piezoelectric signal parameter measuring circuit prototype is constructed, and a BP neural network model for flow prediction of piezoelectric pumps is constructed. The neural network takes voltage parameters and frequency as input parameters to obtain the flow prediction value.
The experimental results show that the correlation coefficient between the predicted value and the measured value is above 0.9993, and the maximum relative error rate is less than 3.46%. The flow self-measuring method has good accuracy, and the flow self-measuring method can also be applied to other types and structures of piezoelectric pumps.
6. precise control method for liquid delivery based on fixed pulse number
Based on the analysis of driving characteristics and output performance of piezoelectric pump, the control method of liquid precise conveying based on constant pulse number is studied. The pulse numerical control circuit is developed and the precise control method of liquid conveying based on constant pulse number is tested and verified. The maximum relative error is 0.424%, and the correlation coefficient is 0.9999. It shows that the precision control method of liquid conveying based on the fixed pulse number is feasible. Therefore, in the case of high precision of fluid conveying, the corresponding pulse number can be calculated according to the conveying volume, and the pulse number can be sent to the piezoelectric pump to realize the fluid conveying. Precision conveyor control.
【學位授予單位】：吉林大學
【學位級別】：博士
【學位授予年份】：2014
【分類號】：TH38;TP273

【參考文獻】

相關期刊論文 前10條

1 張建輝;黎毅力;劉菊銀;徐宇哲;;“Y”形流管無閥壓電泵流場分析[J];北京工業大學學報;2008年02期

2 戰傳娜;張維;李亭;楊長銳;岳釗;牛文成;劉國華;;一種用于生化傳感檢測的壓電式行波微流泵的研究[J];傳感技術學報;2011年11期

3 耿照新;崔大付;王海寧;劉長春;;新型壓電微泵的結構設計與理論分析[J];傳感器與微系統;2006年12期

4 董維杰,孫寶元,崔玉國,楊志欣;基于壓電自感知執行器懸臂梁振動控制[J];大連理工大學學報;2001年01期

5 董維杰,崔玉國,張小軍,李涵;壓電執行器位移自感知方法研究[J];大連理工大學學報;2004年06期

6 莊乾霞,孫寶元,董維杰;自感知壓電微夾鉗研究[J];大連理工大學學報;2004年06期

7 崔玉國;董維杰;孫寶元;楊志欣;;基于積分器的壓電陶瓷自感知執行器研究[J];大連理工大學學報;2006年06期

8 張忠華;孫寶元;錢敏;張軍;;基于多次壓電效應的自感知執行器研究[J];大連理工大學學報;2010年05期

9 蔣丹;李松晶;楊平;;收縮管/擴張管型無閥壓電微泵的動態特性研究[J];工程力學;2011年03期

10 高曉光;杜立群;呂巖;;PZT壓電薄膜無閥微泵[J];功能材料與器件學報;2008年04期

相關博士學位論文 前1條

1 孫曉鋒;雙振子壓電泵設計理論與結構優化技術研究[D];吉林大學;2009年

，

本文編號：2194003