本文選題：組合機構 + Matlab/Simulink�。� 參考：《山東理工大學》2012年碩士論文

【摘要】：隨著科技的不斷發展及人們生活水平的不斷提高,扣壓機的應用領域不斷擴大,環繩專用扣壓機就是扣壓機應用領域上的創新。環繩專用扣壓機的生產自動化水平及其可裝配性都對公司的效益有重要的影響,因此,研究提高扣壓機自動化水平的方法,并在扣壓機的設計階段研究其可裝配性分析問題對公司效益的提高都有很重要的意義。 本文詳細論述了機構創新設計的理論及其發展趨勢,利用機構創新設計的方法之一組合創新法和組合機構的運動學原理,設計了一個新型的組合機構,并將其應用于扣壓機彎繩機構中,實現了繩料彎曲的自動化,運用Matlab/simulink研究了該組合機構的運動學問題,建立并求解了其數學模型,根據數學模型建立了其仿真模型,對機構進行了運動仿真和驗證,直觀的看出了組合機構的運動情況,得出了該組合機構能夠滿足扣壓機彎繩要求的結論。 本文分析了扣壓機的扣壓工藝,設計出了扣壓模具的結構,并對扣壓凹模進行了優化設計,建立并求解了扣壓凹模的縮口力數學模型,用數學的語言表達了優化的問題,利用數學解析法求出了扣壓凹模的最佳凹模錐角,將扣件起皺現象降低到最小程度。 本文還論述了產品的可裝配性分析評價理論的研究現狀及發展趨勢,分析了影響環繩專用扣壓機扣壓�？裳b配性的因素,建立了其可裝配性分析的概念性框圖；利用多層次的模糊綜合評價方法,建立了環繩專用扣壓模的可裝配性評價模型；并利用德爾菲法對環繩專用扣壓機的扣壓模進行了可裝配性評價。
[Abstract]:With the development of science and technology and the improvement of people's living standard, the application field of the buckler is expanding, and the special fastener is the innovation in the application field of the fastener. The production automation level and assembly ability of special fastener for ring rope have an important influence on the benefit of the company. Therefore, the methods to improve the automation level of the fastener are studied. It is of great significance to improve the efficiency of the company to study the analysis of its assemblability in the design stage of the press. In this paper, the theory of mechanism innovation design and its development trend are discussed in detail. A new type of mechanism is designed by means of combination innovation method and kinematics principle of combined mechanism, which is one of the methods of mechanism innovation design. It is applied to the bending rope mechanism of the buckling machine to realize the automation of the rope material bending. The kinematics problem of the combined mechanism is studied by using Matlab/simulink, and its mathematical model is established and solved, and the simulation model is established according to the mathematical model. The kinematic simulation and verification of the mechanism are carried out, the movement of the combined mechanism is intuitively seen, and the conclusion that the combined mechanism can meet the requirements of the bending rope of the buckler is obtained. In this paper, the technology of the buckling machine is analyzed, the structure of the die is designed, the optimum design of the die is carried out, the mathematical model of the shrinkage force of the die is established and solved, and the optimization problem is expressed in mathematical language. The optimum conical angle of the die is obtained by the mathematical analytic method, and the wrinkle phenomenon of the fastener is reduced to the minimum. This paper also discusses the present situation and development trend of the analysis and evaluation theory of product assemblability, analyzes the factors that affect the assemblability of the clamping die of the special ring rope fastener, and establishes the conceptual block diagram for the analysis of the assemblability. In this paper, a multi-level fuzzy comprehensive evaluation method is used to establish the evaluation model of the assemblability of the special fastening die for the ring rope, and the Delphi method is used to evaluate the assemblability of the clamping die of the special fastener for the ring rope.
【學位授予單位】：山東理工大學
【學位級別】：碩士
【學位授予年份】：2012
【分類號】：TH112

【參考文獻】

相關期刊論文 前10條

1 宋玉銀,褚秀萍,蔡復之;基于廣義鍵的產品可裝配性模糊評價方法研究[J];高技術通訊;2000年07期

2 胡成武,鄒安全,陳吉平;基于最小縮口力條件下的縮口凹模傾角[J];鍛壓技術;2004年02期

3 顧寄南,龐偉,張林搚,蔡健敏;基于裝配單元的可裝配性評價技術[J];農業機械學報;2003年03期

4 胡成武,田繼閣;筒形件縮口成形最佳凹模錐角的確定[J];模具工業;2000年10期

5 盧險峰,褚亮;彈殼形狀零件縮口力描述模型研究[J];塑性工程學報;2004年06期

6 褚亮,盧險峰,張朝閣;縮口變形力的計算及其精度比較[J];兵器材料科學與工程;2004年05期

7 顧寄南,歐陽玉秀,肖田元,張林搚;產品可裝配性評價系統建模及裝配優化的研究[J];工程圖學學報;2003年04期

8 陳亞琴,孔凌嘉,張春林;機構疊加組合與創新設計[J];機械設計與研究;2001年04期

9 鄒慧君;張青;王學武;;組合機構的基本特征和設計方法[J];機械設計與研究;2006年01期

10 顧寄南,蔡健敏;產品可裝配性評價技術的研究現狀和發展方向[J];機械設計;2003年12期

相關會議論文 前1條

1 鄒慧君;郭為忠;田永利;;廣義機構與現代機構學[A];第一屆國際機械工程學術會議論文集[C];2000年

相關碩士學位論文 前1條

1 楊超;高壓膠管總成力學模型及其扣壓過程控制系統研究[D];中南大學;2003年

，

本文編號：1923542