本文選題：CATIA + ADAMS　； 參考：《延邊大學》2012年碩士論文

【摘要】：隨著科技的進步和社會信息化的不斷發展,對產品的規模和復雜程度的要求不斷提高,企業間的競爭日益激烈,傳統的制造與設計已經很難適應當前企業的發展需要。因此信息技術應用于新產品研制以及實施途徑的改造,是現代企業生存、發展的必然結果。在這種狀況下,為了提高企業的效率和效益,改進和更新產品的開發模式是當務之急。 本文以CATIA軟件為二次開發平臺,使用VBScript作為編輯工具,對減速器進行參數化設計和自動虛擬裝配。利用SimDesigner for CATIA V5和Pro/E軟件把虛擬樣機導入到動力學分析軟件ADAMS中,建立了減速器的多剛體虛擬樣機系統,具體研究工作如下： 1.在CATIA軟件中,應用VB編程功能編寫程序,生成齒輪模型。由于齒輪傳動減速器應用比較廣泛,為了提高減速器的生產效率,縮短生產周期,提高產品在市場上的競爭力,由此開發出齒輪庫和標準件庫。根據用戶需要,只需輸入所需零件的基本參數,便可相應地生成所需的模型。 2.基于VB編程,把減速器的零件及附件進行全自動虛擬裝配,然后進行干涉分析與檢測。 3.利用插件SimDesigner for CATIA V5和Pro/E軟件把減速器虛擬樣機導入到ADAMS中,并對其傳動部分施加約束和載荷,以便進行動力學仿真以及對仿真結果進行分析,即三根軸的轉動角速度,得到輸入軸、中間軸和輸出軸的轉動角速度隨時間變化曲線,把用兩種方法得到的仿真值與理論值進行比較,分析誤差,進一步說明用兩種方法導入到ADAMS軟件中的可行性和減速器設計的合理性。
[Abstract]:With the progress of science and technology and the continuous development of social information, the demands on the scale and complexity of products are constantly raised, and the competition among enterprises is becoming increasingly fierce, so it is difficult for traditional manufacturing and design to adapt to the development needs of current enterprises.Therefore, the application of information technology in the development of new products and the transformation of implementation ways is the inevitable result of the survival and development of modern enterprises.In this situation, in order to improve the efficiency and efficiency of enterprises, it is urgent to improve and update the product development model.In this paper, using CATIA software as the secondary development platform and VBScript as the editing tool, parametric design and automatic virtual assembly of the reducer are carried out.Using SimDesigner for CATIA V5 and Pro/E software, the virtual prototype is imported into the dynamic analysis software ADAMS, and the multi-rigid virtual prototype system of reducer is established. The specific research work is as follows:1.In CATIA software, VB programming function is used to program and generate gear model.In order to improve the production efficiency, shorten the production cycle and improve the competitiveness of the products in the market, the gear storehouse and the standard parts library are developed because of the wide application of the gear drive reducer.According to the needs of the user, the required model can be generated by simply inputting the basic parameters of the required parts.2.Based on VB programming, the parts and accessories of reducer are assembled by automatic virtual assembly, and then interference analysis and detection are carried out.3.The virtual prototype of the reducer is imported into ADAMS by the plug-in SimDesigner for CATIA V5 and Pro/E software, and the driving part of the reducer is subjected to constraints and loads, so that the dynamic simulation and the analysis of the simulation results are carried out, that is, the rotation angular velocity of the three shafts.The rotational angular velocity curves of input shaft, intermediate shaft and output shaft are obtained. The simulation value obtained by two methods is compared with the theoretical value, and the error is analyzed.The feasibility of importing two methods into ADAMS software and the reasonableness of reducer design are further explained.
【學位授予單位】：延邊大學
【學位級別】：碩士
【學位授予年份】：2012
【分類號】：TH132.46

【引證文獻】

相關碩士學位論文 前1條

1 邵增超;葉片雙面磨拋工具系統及實驗研究[D];吉林大學;2013年

，

本文編號：1741561