【摘要】：在DZ125L定向基材上進行激光直接成形同種材料的定向生長修復,對修復后的DZ125L熔覆組織進行了微觀分析和常溫力學性能測試,并對熔覆組織與定向基材的結合面強度進行了測試。結果表明:激光直接成形DZ125L的組織為外延生長的柱狀晶組織,其一次枝晶間距為8~12μm,二次枝晶退化,熱處理后柱狀晶尺寸增大為30~90μm,柱狀晶基體上析出大量均勻分布的γ′強化相;沉積態柱狀晶組織的縱向抗拉強度為1312 MPa,延伸率為5.27%,熱處理后柱狀晶組織的縱向抗拉強度降低為1201 MPa,延伸率達到6.69%,均滿足國家標準;熔覆層柱狀晶組織與定向基材的結合面力學性能良好,定向生長滿足使用要求。
[Abstract]:The laser direct forming of the same material was carried out on the DZ125L oriented substrate. The microstructure of the DZ125L cladding after repairing was analyzed and the mechanical properties at room temperature were tested. The strength of the bonding surface between the cladding structure and the oriented substrate was also measured. The results show that the structure of DZ125L grown by laser is columnar structure grown by epitaxial growth. The primary dendrite spacing is 812 渭 m, the secondary dendrite degenerates, and the columnar crystal size increases to 30 ~ 90 渭 m after heat treatment. A large number of uniformly distributed 緯 'strengthened phases were precipitated on the columnar matrix. The longitudinal tensile strength of the deposited columnar structure is 1312 MPa, and the longitudinal tensile strength of the columnar structure decreases to 1201 MPa, after heat treatment, which meets the national standard. The mechanical properties of the bonding surface of the cladding columnar crystal structure and the oriented substrate are good, and the directional growth meets the requirements of application.
【作者單位】： 西安交通大學機械制造系統工程國家重點實驗室;
【基金】：國家自然科學基金(51275392)
【分類號】：TG665

【參考文獻】

相關期刊論文 前10條

1 ;Directional Solidification Assisted by Liquid Metal Cooling[J];Journal of Materials Science & Technology;2007年03期

2 胡小華;張安峰;李滌塵;魯中良;賀斌;葛江波;;熱處理對激光金屬成形DZ125L高溫合金組織及硬度的影響[J];材料工程;2013年02期

3 陳榮章,佘力,張宏煒,王羅寶;DZ125定向凝固高溫合金的研究[J];航空材料學報;2000年04期

4 智翔;趙劍峰;蔡軍;;激光熔覆修復工藝參數對熔合區成形質量的影響[J];激光與光電子學進展;2011年10期

5 葛江波;張安峰;李滌塵;朱剛賢;路橋潘;賀斌;魯中良;;激光金屬直接成形DZ125L高溫合金零件工藝的研究[J];中國激光;2011年07期

6 劉其斌;李紹杰;;航空發動機葉片鑄造缺陷激光熔覆修復的研究[J];金屬熱處理;2006年03期

7 Doan Tatkhoa;李滌塵;盧秉恒;張安峰;賀斌;Do Xuantuoi;;掃描方式對激光金屬直接成形DZ125L高溫合金薄壁件開裂的影響[J];中國激光;2012年10期

8 潘滸;趙劍峰;劉云雷;王凱;肖猛;高雪松;;激光熔覆修復鎳基高溫合金稀釋率的可控性研究[J];中國激光;2013年04期

9 Do Xuantuoi;李滌塵;張安峰;賀斌;;激光金屬直接成形DZ125L高溫合金柱狀晶連續生長的數值模擬與實驗研究[J];中國激光;2013年06期

10 羅W，

本文編號：2388941