【摘要】：板料數控漸進成形中不同成形角位置的厚度不同,簡單利用零件曲面或者等距偏置無法保證得到工具頭與支撐體的合理間隙。利用漸進成形厚度減薄余弦定理δ=δ0cosθ,將加工件的表面離散為STL模型,提取STL各三角面片頂點坐標,x、y坐標保持不變,z坐標在Z軸負向偏置一個原始板材厚度,偏置后保持三角片拓?fù)潢P(guān)系不變,在此基礎上生成支撐體表面模型。該方法依據零件模型不同成形角部位的厚度變化規律,可以得到合理的加工間隙。選擇球冠型零件進行實驗,獲得了較好的加工件表面質量,對成形零件變形區厚度進行了測量,并對所得數據進行分析。
[Abstract]:The thickness of different position of forming angle is different in NC incremental forming of sheet metal. The reasonable gap between tool head and support can not be obtained simply by using part surface or offset. By using the cosine theorem 未 = 未 0cos 胃 of progressive forming thickness thinning, the surface of the workpiece is discretized into a STL model, and the vertex coordinates of the STL triangles are extracted. The xy coordinates remain the same, and the z coordinates are biased negatively on the Z axis to the original plate thickness. After bias, the topological relation of the triangulation is kept unchanged, and the surface model of the support is generated on the basis of this. The method can obtain reasonable machining clearance according to the thickness variation of different forming angles of the part model. The surface quality of the workpiece is obtained and the thickness of the deformation zone of the formed part is measured and the data obtained are analyzed.
【作者單位】： 南京工程學院材料工程學院;江蘇省先進結構材料與應用技術重點實驗室;南京交通職業技術學院;
【基金】：江蘇省先進結構材料與應用技術重點實驗室開放基金(ASMA201410) 南京工程學院創新基金項目(CKJB201304,CKJB201402;YKJ201311) 江蘇省大學生實踐創新項目(201511276041Y)
【分類號】：TG306

【相似文獻】

相關期刊論文 前2條

1 朱虎;楊曉光;;五軸數控漸進成形干涉檢測與修正研究[J];機械工程學報;2014年07期

2 ;[J];;年期

，

本文編號：2339065