【摘要】：基于雙軸柔性滾彎技術原理,建立了采用0Cr15Ni7Mo2Al材料制備小直徑開縫襯套過程的三維有限元模型,以指導實際小直徑開縫襯套的制備。利用該模型分析了襯套應力應變分布、剛性軸受力變形情況、襯套成形曲率半徑與剛性軸直徑的關系及襯套成形曲率半徑與帶材尺寸的關系,并用滾彎試驗驗證了該模型的準確性。結果說明:帶材滾彎變形隨著進給量的增加而更均勻;剛性軸受力隨其直徑的減小而減小,剛性軸變形程度隨其直徑的減小而增大;襯套成形曲率半徑隨著剛性軸直徑的增大而增大;襯套成形曲率半徑隨著帶材寬度和厚度的增大而增大。
[Abstract]:Based on the principle of biaxial flexible roll bending, a three-dimensional finite element model for the preparation of small diameter slit bushing with 0Cr15Ni7Mo2Al material was established to guide the preparation of practical small diameter slit bushing. By using this model, the stress and strain distribution of the bushing, the stress and deformation of the rigid shaft, the relationship between the forming curvature radius of the bushing and the diameter of the rigid shaft, and the relationship between the forming curvature radius of the bushing and the size of the strip are analyzed. The accuracy of the model is verified by rolling bending test. The results show that the rolling bending deformation of the strip is more uniform with the increase of the feed rate, the force of the rigid axis decreases with the decrease of its diameter, and the degree of deformation of the rigid axis increases with the decrease of its diameter. The forming curvature radius of the bushing increases with the increase of the diameter of the rigid shaft, and the radius of the forming curvature increases with the increase of the width and thickness of the strip.
【作者單位】： 南京航空航天大學;
【基金】：空裝十一五項目 中央高�；究蒲袠I(yè)務費專項資金資助項目(kfjj130118) 南京航空航天大學2013年度研究生創新基地(實驗室)開放基金資助項目(kfjj130118)
【分類號】：TG306

【參考文獻】

相關期刊論文 前10條

1 閆靜,左敦穩,王珉;雙軸柔性滾彎過程中工件回彈的理論分析[J];兵工學報;2003年03期

2 何祝斌;林艷麗;孫紅巖;;型材單輥柔性墊彎曲曲率半徑變化規律研究[J];材料科學與工藝;2012年05期

3 丁傳富，趙振業，，宋德玉;孔擠壓強化對兩種超高強度鋼疲勞裂紋起始與擴展壽命的影響[J];航空學報;1994年08期

4 陳國輝;張小聰;羅承萍;劉江文;劉志堅;;沉淀硬化不銹鋼PH15-7Mo的時效行為[J];金屬熱處理;2010年07期

5 閆靜,左敦穩,王珉;雙軸柔性滾彎技術的有限元分析[J];機械科學與技術;2003年02期

6 楊洪源;劉文s

本文編號：2287973