微細側銑過程的有限元建模與仿真（英文）
發布時間：2018-07-23 17:54
【摘要】：建立了AISI 4340微細側銑的二維有限元模型。將Johnson-Cook本構模型與JohnsonCook剪切失效模型相結合,對銑削刃旋轉過程中的一個完整側銑周期進行了仿真。由于沒有考慮尺寸效應的影響,所得到的流動應力值偏小。因此,建立了應變梯度塑性模型,并應用其預測了切屑的形成、馮米斯應力和溫度場。仿真結果顯示:微細側銑過程中存在尺度效應,與Johnson-Cook本構模型相比,應變梯度塑性模型能夠很好地描述微細側銑過程中的尺寸效應。最后,將仿真結果與理論計算結果相比較,驗證了所建模型的正確性。
[Abstract]:A two-dimensional finite element model of AISI 4340 micro-side milling is established. The Johnson-Cook constitutive model and the JohnsonCook shear failure model are combined to simulate a complete side milling cycle in the process of milling edge rotation. Because the size effect is not considered, the flow stress is smaller. Therefore, a strain gradient plastic model is established and applied to predict chip formation, Vonmins stress and temperature field. The simulation results show that there is a scale effect in the process of micro side milling. Compared with the Johnson-Cook constitutive model, the strain gradient plastic model can well describe the size effect in the process of micro side milling. Finally, the correctness of the model is verified by comparing the simulation results with the theoretical results.
【作者單位】： 重慶科技學院機械與動力工程學院;中核核電運行管理有限公司;
【基金】：supported by Chongqing Research Program of Basic Research and Frontier Technology (No.cstc2013jcyj A70004) Scientific and Technological Research Program of Chongqing Municipal Education Commission (No.KJ1501314 ) Chongqing University of Science & Technology (No.CK2014Z27)
【分類號】：TG54
本文編號：2140181
[Abstract]:A two-dimensional finite element model of AISI 4340 micro-side milling is established. The Johnson-Cook constitutive model and the JohnsonCook shear failure model are combined to simulate a complete side milling cycle in the process of milling edge rotation. Because the size effect is not considered, the flow stress is smaller. Therefore, a strain gradient plastic model is established and applied to predict chip formation, Vonmins stress and temperature field. The simulation results show that there is a scale effect in the process of micro side milling. Compared with the Johnson-Cook constitutive model, the strain gradient plastic model can well describe the size effect in the process of micro side milling. Finally, the correctness of the model is verified by comparing the simulation results with the theoretical results.
【作者單位】： 重慶科技學院機械與動力工程學院;中核核電運行管理有限公司;
【基金】：supported by Chongqing Research Program of Basic Research and Frontier Technology (No.cstc2013jcyj A70004) Scientific and Technological Research Program of Chongqing Municipal Education Commission (No.KJ1501314 ) Chongqing University of Science & Technology (No.CK2014Z27)
【分類號】：TG54
【相似文獻】
相關期刊論文 前4條
1 趙洪壯;LEE Seok-jae;LEE Young-kook;劉相華;王國棟;;奧氏體化時間對AISI 4340鋼貝氏體連續轉變動力學的影響[J];材料熱處理學報;2006年04期
2 趙洪壯;LEE Young-kook;劉相華;王國棟;;奧氏體晶粒度對AISI 4340鋼貝氏體相變動力學的影響[J];材料熱處理學報;2006年02期
3 彥卿;AISI 4340鋼的激光氮化[J];鋼鐵研究總院學報;1988年03期
4 ;[J];;年期
相關會議論文 前1條
1 章小滸;陸戴丁;;在役AISI 4340鋼設計疲勞曲線試驗研究[A];第四屆全國壓力容器學術會議論文集[C];1997年
，本文編號：2140181
本文鏈接：http://sikaile.net/kejilunwen/jinshugongy/2140181.html
最近更新
教材專著
