【摘要】：采用鎂砂粉和剛玉粉作為耐火骨料制備了一種燒結型鑄型涂料,實驗研究了兩種骨料的適宜配比,分析了骨料組元比例對燒結過程的影響;優化設計了一種以鎂砂粉和剛玉粉為復合耐火骨料的鑄型涂料配比,檢測了涂料的性能。結果表明:復合骨料燒結后的涂層產生了鎂鋁尖晶石(Mg Al_2O_4),當鎂砂粉和剛玉粉混合質量為7∶3時,涂層中的Al_2O_3全部參與燒結反應;硅溶膠(SiO_2·n H_2O)的加入可以改善涂層的高溫強度,防止出現暴熱裂紋;優化后的涂料具有較好的綜合性能,能有效地防止不銹鋼鑄件表面出現粘砂現象。
[Abstract]:A sintered mold coating was prepared by using magnesia and corundum powder as refractory aggregate. The optimum ratio of two kinds of aggregate was studied experimentally and the effect of the ratio of aggregate component on the sintering process was analyzed. A kind of casting coating with magnesia powder and corundum powder as composite refractory aggregate was designed and the properties of the coating were tested. The results show that the magnesia-alumina spinel (MgAl2O4) is produced after the composite aggregate is sintered. When the mixture mass of magnesia and corundum powder is 7:3, all AlStat _ 2O _ 3 in the coating take part in the sintering reaction, and the high temperature strength of the coating can be improved by adding silica sol (Sio _ 2n H _ 2O). The optimized coating has good comprehensive properties and can effectively prevent the appearance of sand on the surface of stainless steel castings.
【作者單位】： 沈陽工業大學材料科學與工程學院;
【基金】：沈陽市工業攻關計劃項目(F12-008-2-00)
【分類號】：TG221

【相似文獻】

相關期刊論文 前6條

1 劉貫軍;剛玉粉涂料的應用實踐[J];機械工人;1997年05期

2 于敏喜;;煤矸石在鑄造工藝中的應用[J];新技術新工藝;1985年04期

3 劉瑞諾;張戰號;田衛國;;剛玉粉對強化木地板耐磨轉數影響淺析[J];中國人造板;2010年09期

4 吳國定;剛玉粉涂料鑄造高鋁鎳鈷鈦磁鐵[J];特種鑄造及有色合金;1984年04期

5 潘大海,劉梅;剛玉粉對室溫硫化導熱硅橡膠性能的影響[J];有機硅材料;2004年06期

6 ;[J];;年期

相關碩士學位論文 前1條

1 袁志麗;Sialon結合SiC材料的制備與性能研究[D];西安建筑科技大學;2008年

，

本文編號：2123817