本文選題：再生WC-Co復合粉 + 硬質合金涂層��； 參考：《中國有色金屬學報》2015年12期

【摘要】：以WC-6Co廢舊硬質合金塊體和Co_3O_4粉末為原料,采用氧化-還原碳化法制備再生WC-12Co復合粉,將復合粉經過造粒和熱處理制備再生熱噴涂喂料,進而采用超音速火焰噴涂(HVOF)制備再生WC-Co硬質合金涂層,比較再生硬質合金涂層和商業購買熱噴涂喂料制備涂層的顯微組織、耐磨性及其機制。結果表明:當配碳量為16.70%(質量分?jǐn)?shù))時,再生復合粉的碳含量適中;制備的再生熱噴涂喂料由WC和Co相組成,熱噴喂料球形度好,粒徑分布均勻,平均粒徑為23μm;再生WC-12Co硬質合金涂層的結構致密,WC晶粒尺寸分布均勻。與商業化熱噴涂粉制備涂層顯微組織和性能相比,再生涂層的磨粒磨損性能明顯優于商業噴涂粉制備涂層的,其根本原因是兩者的磨損機制不同。
[Abstract]:The regenerated WC-12Co composite powder was prepared by oxidation-reduction carbonization method from WC-6Co waste cemented carbide block and Cos _ 3O _ s _ 4 powder. The composite powder was granulated and heat treated to prepare regenerated hot spraying feedstock. Furthermore, the microstructure, wear resistance and mechanism of regenerated WC-Co cemented carbide coatings were compared with those prepared by commercial hot spraying and reclaimed WC-Co cemented carbide coatings prepared by hypersonic flame spraying (HVOF). The results show that the carbon content of the regenerated composite powder is moderate when the carbon content is 16.70%, the prepared regenerated hot spray feedstock is composed of WC and Co phase, the hot spray feed has good globality and uniform particle size distribution. The average particle size is 23 渭 m, and the grain size distribution of WC-12Co cemented carbide coating is uniform. Compared with the microstructure and properties of the coatings prepared by commercial thermal spraying powder, the abrasive wear properties of the regenerated coatings are obviously superior to those of the coatings prepared by commercial spraying powder. The fundamental reason is that the wear mechanisms of the two coatings are different.
【作者單位】： 北京工業大學材料科學與工程學院;
【基金】：國家高新技術研究發展計劃主題項目(SQ2013AAJY3168) 國家自然科學基金資助項目(51174009) 北京市自然科學基金重點資助項目(2131001)
【分類號】：TG174.4

【參考文獻】

相關期刊論文 前2條

1 丁彰雄;陳偉;王群;;超音速火焰噴涂制備多峰WC-12Co涂層的抗汽蝕性能(英文)[J];Transactions of Nonferrous Metals Society of China;2011年10期

2 李學偉;孟銀;王鵬;程浩然;;熱噴涂WC-10Co4Cr涂層的研究現狀[J];中國鎢業;2014年02期

【共引文獻】

相關期刊論文 前4條

1 丁彰雄;萬文晨;趙輝;劉霽;;熱噴涂WC-Co復合涂層的研究現狀及展望[J];熱噴涂技術;2012年02期

2 石t;丁翔;胡一鳴;丁彰雄;肖俊鈞;王韶毅;;WC基涂層材料和制備工藝對其組織結構與性能的影響[J];熱噴涂技術;2015年02期

3 陳文;龍安平;向錦濤;李松林;周伍喜;李玉璽;;超音速火焰噴涂WC-10Co4Cr涂層在NaCl溶液中的耐腐蝕性能[J];中南大學學報(自然科學版);2014年10期

4 王群;屈幫榮;唐w線，

本文編號：2046469