本文選題：激光熔覆 + 摩擦磨損�。� 參考：《材料熱處理學報》2015年08期

【摘要】：采用激光熔覆對304不銹鋼表面處理得到不同的熔覆層,研究了激光功率和粉末成分對涂層磨損量以及摩擦系數的影響。利用CETR UMT-2型摩擦磨損試驗機進行干滑動磨損試驗,采用SURFCOM 130A型粗糙度儀掃描熔覆層表面磨痕,采用ESM及EDS觀察磨損表面形貌,分析其磨損形式。結果表明:C類涂層(Ni60:92%,C;2%,Mo S2:6%)在1.8 k W激光下制備的涂層C2的磨損量為1.452×10-2mm3,相對耐磨性達到基體的6.39倍,磨損形式主要為疲勞磨損,伴隨輕微磨粒磨損;E類涂層(Ni60:92%,C:6%,Mo S2:2%)在2.0 k W激光下制備的涂層E3的磨損量?jī)H為0.925×10-2mm3,耐磨性最好,磨損形式主要為磨粒磨損;添加潤滑相的E3涂層的摩擦系數高于C2,但是在整個實驗過程中比較穩定;磨損特性的改善表明石墨與Mo S2之間有良好的協同效應。
[Abstract]:Different cladding layers were obtained by laser cladding on 304 stainless steel surface. The effects of laser power and powder composition on the wear and friction coefficient of the coating were studied. Dry sliding wear test was carried out by using CETR UMT-2 friction and wear tester. Wear marks were scanned by surfcom 130A rough degree instrument. ESM and EDS were used to observe the wear surface morphology and its wear form was analyzed. The results show that the wear capacity of the coating C2 prepared under 1.8 kW laser is 1.452 脳 10 ~ (-2) mm ~ (3), and the relative wear resistance is 6.39 times that of the substrate. The wear form of C _ 2 coating is mainly fatigue wear, and the wear rate of C _ 2 is 1.452 脳 10 ~ (-2) mm ~ (-3). The wear rate of the coating E3 prepared under 2.0 kW laser is only 0.925 脳 10 ~ (-2) mm ~ (3), the wear resistance is the best, and the wear form is mainly abrasive wear. The friction coefficient of E3 coating with lubricating phase is higher than that of C _ 2, but it is stable in the whole experiment process, and the improvement of wear characteristics indicates that there is a good synergistic effect between graphite and MoS _ 2.
【作者單位】： 溫州大學機電工程學院;江蘇大學機械工程學院;常州光電技術研究院;
【基金】：科技部中俄雙邊政府間2014-2015科技合作項目(CR17-11) 浙江省國際科技合作專項(2013C14007) 國家自然科學基金項目(51175237,51305050) 溫州市工業科技研究開發項目(J20130033)
【分類號】：TG174.4

【參考文獻】

相關期刊論文 前8條

1 路程;劉江文;馬文有;陳和興;;激光熔覆鎳基合金層的組織與高溫耐磨性能[J];材料保護;2012年02期

2 薛敏鵬;韓彬;王勇;劉興光;;激光熔覆Ni基WC/Cr_3C_2涂層顯微組織和耐蝕性研究[J];激光與光電子學進展;2011年09期

3 朱文慧;徐江;陳哲源;劉文今;;鋁合金表面激光熔覆原位自生TiB顆粒增強耐磨涂層的研究[J];材料熱處理學報;2007年S1期

4 張魁武;國外激光熔覆材料、工藝和組織性能的研究[J];金屬熱處理;2002年06期

5 王賽玉,熊惟皓;激光技術在材料科學中的應用[J];金屬熱處理;2005年07期

6 徐鵬;林成新;周超玉;宋志成;;激光熔覆304不銹鋼涂層的工藝及組織[J];材料熱處理學報;2013年07期

7 張滿奎;孫桂芳;張尉;劉衛祥;王昆;;不銹鋼表面激光合金化Cr-CrB_2層的腐蝕性研究[J];激光技術;2014年02期

8 蔡振兵;朱e，

本文編號：1997424