本文選題：磨料水射流 + 沖擊變形磨損　； 參考：《機械工程學報》2015年07期

【摘要】：采用ANSYS Fluent對磨粒流場進行瞬態CFD仿真,得到射流過程中磨粒的分布和速度;并研究射流加工區磨粒運動機制,研究表明,新型后混合式磨料水射流加工中磨粒很容易穿過射流加工的靜壓區直接與工件發生作用進而去除材料。建立磨粒沖擊塑性材料的沖擊變形磨損模型,并結合Finnie塑性剪切磨損去除模型建立磨料水射流加工去除模型,模型表明,射流加工中心區域的材料去除量最高。根據新型后混合式磨料水射流系統進行塑性材料的磨料水射流加工試驗,結果表明,射流加工中心區域材料去除最高,這是由于射流加工中心區域磨粒沖擊角度較大、磨粒速度較高,材料以沖擊變形磨損去除為主;遠離射流沖擊中心區域材料去除較低,材料以剪切磨損去除為主,與磨料水射流加工去除模型是完全一致的,證實磨料水射流加工去除模型的正確性。
[Abstract]:The distribution and velocity of abrasive particles in the jet process are obtained by transient CFD simulation of the flow field of abrasive particles by ANSYS Fluent, and the motion mechanism of abrasive particles in the jet processing zone is studied. In the new type of post-mixed abrasive water jet machining, the abrasive particles can easily pass through the static pressure zone of the jet processing and directly interact with the workpiece and then remove the material. The impact deformation and wear model of abrasive impingement plastic materials and the Finnie plastic shear wear removal model are established. The model shows that the material removal rate is the highest in the central area of jet machining. According to the new type of post-mixed abrasive water jet system, the abrasive water jet processing test of plastic material is carried out. The results show that the material removal in the center of jet machining is the highest, which is due to the large impact angle of abrasive particles in the area of jet machining center. The abrasive particle velocity is higher, the material is mainly removed by impact deformation and wear, the material removed from the center of jet impingement is lower, and the material is mainly removed by shear wear, which is completely consistent with the removal model of abrasive water jet machining. It is proved that the removal model of abrasive water jet machining is correct.
【作者單位】： 哈爾濱工業大學機電工程學院;
【基金】：國家自然科學基金(51275116) 航空科學基金(2012EE77010) 黑龍江省博士后啟動基金(LBH-Q11090)資助項目
【分類號】：TG664

【參考文獻】

相關期刊論文 前6條

1 方慧;郭培基;余景池;;液體噴射拋光技術材料去除機理的有限元分析[J];光學精密工程;2006年02期

2 施春燕;袁家虎;伍凡;萬勇建;;沖擊角度對射流拋光中材料去除面形的影響分析[J];光學學報;2010年02期

3 計時鳴;唐波;譚大鵬;宮斌;袁巧玲;潘艷;;結構化表面軟性磨粒流精密光整加工方法及其磨粒流動力學數值分析[J];機械工程學報;2010年15期

4 王星;張勇;張飛虎;張玲花;周明;;納米顆粒膠體動壓空化射流拋光技術初探(英文)[J];納米技術與精密工程;2011年06期

5 袁巨龍;吳U，

本文編號：1973909