本文選題：316不銹鋼 + 冷軋�。� 參考：《燕山大學》2015年碩士論文

【摘要】：本文采用二輥軋機和激光處理設備對316不銹鋼進行冷軋和激光表面處理,通過金相、X射線衍射、硬度及電化學等方法探究激光處理對固溶態和冷軋態316不銹鋼微觀組織和性能的影響。研究結果表明:316不銹鋼經過冷軋后顯微硬度隨著軋制變形量的增加逐漸增大,軋制變形量50%時組織中出現形變誘發馬氏體,此后變形量增大馬氏體含量增多。冷軋使得316不銹鋼的點蝕電位下降,增大了其晶間腐蝕敏感性,但是點蝕發生后鈍化膜的修復能力增強。固溶態316不銹鋼經過激光處理后晶粒內部發生滑移,隨激光處理溫度升高和次數增大,層錯概率、位錯密度、微應變及顯微硬度增大,但孿晶概率和微晶尺寸下降,晶粒內部形成了許多小角度晶界。激光處理降低了固溶態316不銹鋼的點蝕電位,但增強了點蝕發生時鈍化膜的修復能力,固溶316不銹鋼激光處理后的晶間腐蝕敏感性增大。冷軋態(變形量80%)316不銹鋼經過激光處理后發生了馬氏體向奧氏體的逆轉變。隨激光處理的溫度升高和次數增大,層錯概率、位錯密度、微應變和微晶尺寸減小,激光處理區的顯微硬度下降。激光處理提高了冷軋態316不銹鋼的點蝕電位但使鈍化膜的修復能力減弱,經過激光處理后冷軋態不銹鋼的晶間腐蝕敏感性降低。
[Abstract]:In this paper, the cold rolling and laser surface treatment of 316 stainless steel were carried out by two high rolling mill and laser treatment equipment, and the X-ray diffraction of 316 stainless steel was carried out by metallographic X-ray diffraction. The effect of laser treatment on microstructure and properties of 316 stainless steel in solid solution and cold rolled state was investigated by means of hardness and electrochemistry. The results show that after cold rolling, the microhardness increases gradually with the increase of rolling deformation, and the deformation induced martensite appears in the microstructure at the rolling deformation rate of 50 and the content of martensite increases thereafter. Cold rolling decreases the pitting potential of 316 stainless steel and increases its sensitivity to intergranular corrosion, but the repair ability of the passivation film increases after pitting. After laser treatment, the grain slip occurs in 316 stainless steel. With the increase of temperature and times of laser treatment, the probability of stacking fault, dislocation density, microstrain and microhardness increase, but the twin probability and microcrystalline size decrease. Many small angle grain boundaries are formed inside the grains. Laser treatment reduced the pitting potential of the solution 316 stainless steel, but enhanced the repair ability of the passivation film during the pitting corrosion. The intergranular corrosion sensitivity of the laser treated 316 stainless steel was increased. After laser treatment, the reverse transformation of martensite to austenite occurred in cold-rolled stainless steel (80 and 316 stainless steel). With the increase of temperature and times of laser treatment, the probability of stacking fault, dislocation density, microstrain and microcrystalline size decrease, and the microhardness of laser treatment region decreases. The pitting potential of cold-rolled 316 stainless steel was increased by laser treatment, but the repair ability of passivation film was weakened, and the intergranular corrosion sensitivity of cold-rolled stainless steel decreased after laser treatment.
【學位授予單位】：燕山大學
【學位級別】：碩士
【學位授予年份】：2015
【分類號】：TG665;TG142.71

【參考文獻】

相關期刊論文 前4條

1 郎豐軍;阮偉慧;李謀成;沈嘉年;;溫度對316L不銹鋼耐海水腐蝕性能的影響[J];腐蝕科學與防護技術;2012年01期

2 張素銀;杜凱;諶加軍;詹勇軍;曾體賢;;電解拋光技術研究進展[J];電鍍與涂飾;2007年02期

3 許適群;不銹鋼的耐蝕性能[J];石油化工腐蝕與防護;2005年05期

4 高娃,羅建民,楊建君;雙相不銹鋼的研究進展及其應用[J];兵器材料科學與工程;2005年03期

，

本文編號：1922045