本文選題：高強度鋼 + 沖裁過程��； 參考：《上海交通大學學報》2015年10期

【摘要】：針對傳統的擴孔模擬方法未考慮沖裁變形過程而導致預測精度較低的問題,以高強度DP590鋼為例,對沖裁-擴孔的全過程進行數值模擬.采用改進的積分方法獲得Oyane韌性斷裂準則的閾值,基于沖裁變形的應變梯度分布與損傷分布進行擴孔工序的模擬,并與其實驗結果加以對比.結果表明:與未考慮沖裁變形過程的預測結果相比,考慮沖裁變形過程的預測精度提高了99.6%;沖裁間隙越大(10%~15%),其仿真結果與實驗結果吻合越好.
[Abstract]:In order to solve the problem that the traditional simulation method of hole expansion does not consider the process of blanking deformation, the prediction accuracy is low. Taking high strength DP590 steel as an example, the numerical simulation of the whole process of blanking and reaming is carried out. The threshold value of Oyane ductile fracture criterion is obtained by using the improved integral method. Based on the strain gradient distribution and damage distribution of blanking deformation, the pore expansion process is simulated and compared with the experimental results. The results show that compared with the prediction results without considering the blanking deformation process, the prediction accuracy of the blanking deformation process is increased 99.66.The larger the blanking gap is, the better the simulation results are with the experimental results.
【作者單位】： 上海交通大學模具CAD國家工程研究中心;
【基金】：國家自然科學基金項目(51105246,51105250)資助
【分類號】：TG386.2

【參考文獻】

相關碩士學位論文 前1條

1 周蕾;高強度鋼板沖切模具磨損特性及沖切試樣斷面特征研究[D];上海交通大學;2012年

【共引文獻】

相關期刊論文 前8條

1 Yanshan Lou;Hoon Huh;;EVALUATION OF DUCTILE FRACTURE CRITERIA IN A GENERAL THREE-DIMENSIONAL STRESS STATE CONSIDERING THE STRESS TRIAXIALITY AND THE LODE PARAMETER[J];Acta Mechanica Solida Sinica;2013年06期

2 范春雷;張青艷;劉芳;聶寶磊;;關于QP980CR鋼焊接結構動態拉伸的實驗研究[J];經營管理者;2015年13期

3 路家斌;曾軍;閻秋生;;圓盤剪分切斷面形貌形成機理研究[J];機械工程學報;2014年11期

4 曾軍;路家斌;閻秋生;;鍍鋅板圓盤剪分切過程材料形變機理研究[J];機電工程技術;2014年04期

5 ZHUANG XinCun;XU Cheng;ZHAO Zhen;;Experimental and numerical investigation of failure mode in geometrically imperfect DP590 steel[J];Science China(Technological Sciences);2015年03期

6 吳磊;劉彬;丁立剛;;圓管大直徑外翻邊孔加工工藝設計與翻邊力計算（英文）[J];機床與液壓;2015年18期

7 Yong-Gang Deng;Hong-Shuang Di;Jie-Cen Zhang;;Effect of Heat-Treatment Schedule on the Microstructure and Mechanical Properties of Cold-Rolled Dual-Phase Steels[J];Acta Metallurgica Sinica(English Letters);2015年09期

8 鄭歡;吳彥駿;刁可山;莊新村;陳R際，

本文編號：1891539