本文選題：切削液 + 綠色制造��； 參考：《重慶大學學報》2015年06期

【摘要】：切削液的合理選擇是提高切削加工綠色化程度的重要途徑之一。根據綠色制造原理,在首先滿足加工質量的前提下,建立了一種綜合考慮時間、質量、成本、資源消耗和環境影響5個因素的切削液評價體系。采用油基切削液和不同類型的水基切削液進行剃齒加工對比試驗,從工件質量、刀具壽命、成本和資源環境影響幾個方面進行對比分析。結合試驗結果,利用模糊綜合評價方法對加工結果進行了評價,并據此提出了用于剃齒加工的切削液綜合選擇模型,通過剃齒加工實例驗證了該模型的可行性。試驗證明:采用水基切削液進行剃齒加工仍能滿足質量要求,與傳統油基切削液相比,水基能有效降低生產成本,同時減少對環境的污染。
[Abstract]:The reasonable choice of cutting fluid is one of the important ways to improve the green degree of cutting.According to the principle of green manufacturing, a cutting fluid evaluation system considering five factors such as time, quality, cost, resource consumption and environment was established on the premise of satisfying the quality of machining.A comparative experiment of shaving with oil based cutting fluid and different water based cutting fluid was carried out. The effects of workpiece quality, tool life, cost and resource and environment were compared and analyzed.Combined with the experimental results, the fuzzy comprehensive evaluation method is used to evaluate the machining results, and a comprehensive selection model of cutting fluid for gear shaving is put forward, and the feasibility of the model is verified by an example of shaving.The experiments show that the water-base cutting fluid can still meet the quality requirements. Compared with the traditional oil-based cutting fluid, the water-based cutting fluid can effectively reduce the production cost and reduce the pollution to the environment.
【作者單位】： 重慶大學機械傳動國家重點實驗室;重慶大學機械工程學院;重慶大學制造工程研究所;
【基金】：國家科技支撐計劃資助項目(2012BAF13B09)~~
【分類號】：TG501.5

【參考文獻】

相關期刊論文 前1條

1 孫建國,葛培琪,劉鎮昌;基于生命周期分析的綠色切削液模糊綜合評價[J];潤滑與密封;2001年04期

【共引文獻】

相關期刊論文 前10條

1 樊國福，喻秉倫，李惕冰，許世杰，李婕;特種乳化切削油的研究[J];材料保護;1995年06期

2 陳志莉,楊官漢,婁方,王立光,葉茂平;廢線切割液絮凝破乳的研究[J];重慶環境科學;2000年06期

3 沈昊宇;李R，

本文編號：1736195