本文關鍵詞：激光熱絲焊電阻熱控制及送絲參數優化　出處：《焊接學報》2015年09期 　論文類型：期刊論文

  更多相關文章： 激光熱絲焊 電阻熱優化 高速攝像 紅外雙色測溫 數值模擬

【摘要】：如何選擇送絲參數從而獲得合適電阻熱是確保焊絲穩定過渡和高效熔覆的必要條件.文中通過高速攝像觀察電阻熱對焊絲過渡行為的影響,采用紅外雙色測溫對焊絲溫度進行測量.結果表明,導電嘴以下30 mm處焊絲的溫度可作為最優電阻熱的判據;利用數值模擬方法建立了焊絲非穩態導熱模型,計算了導電嘴以下30 mm處焊絲的溫度,從而可以預測最優電阻熱對應的送絲參數.對不同送絲速度下最優電流比較發現,一定電阻熱下加熱電流的平方與送絲速度的比值為常數,可用于快速選擇最優電阻熱的送絲參數.
[Abstract]:How to select the wire feeding parameters to obtain the appropriate resistance heat is a necessary condition to ensure the stable transition and high efficiency cladding of the welding wire. The influence of the resistance heat on the wire transition behavior is observed by high speed camera in this paper. The temperature of welding wire is measured by infrared two-color temperature measurement. The results show that the temperature of wire below 30 mm of conductive nozzle can be used as the criterion of optimum resistance heat. The unsteady heat conduction model of welding wire is established by numerical simulation, and the temperature of welding wire is calculated at 30 mm below the conductive nozzle. It is found that the ratio of the square of heating current to the feeding speed is constant for the comparison of the optimal current at different feeding speeds. Can be used to quickly select the optimal resistance heat feeding parameters.
【作者單位】： 清華大學機械工程系;清華大學先進成形制造教育部重點實驗室;
【基金】：國家自然科學基金資助項目(51005125) 國家重點基礎研究發展計劃資助項目(2011CB013404)
【分類號】：TG456.7
【正文快照】： 0序言激光熱絲焊利用電阻熱將焊絲預加熱后送入熔池,減小了焊絲熔化對激光熱量的依賴,不僅降低了焊絲與激光相對位置的精度要求,而且提升了填充效率,是一種有發展前景的激光填絲焊技術,目前已在表面堆焊[1-3]和窄間隙焊接[4]中得到應用.例如日本的日立-巴布科克公司利用激光熱

【參考文獻】

相關期刊論文 前2條

1 肖榮詩,左鐵釧,G，

本文編號：1435691