【摘要】：2013年新交規首次明確提出客運車內的所有乘客均需佩戴安全帶，否則科以罰金。安全帶提醒裝置作為提高安全帶佩戴率的有效方法之一，每一個車輛均有安裝，但是現有安全帶提醒裝置的提醒對象僅僅指駕駛位和副駕駛位，而忽略了車內后排乘客的提醒。對于客運車而言，雖然有駕駛員以“喊話”的傳統方式提醒后排乘客佩戴安全帶，但每年的客運車事故報告表明，總有部分乘客因未佩戴安全帶出現傷亡。因此，為了提高客運車安全帶佩戴率，降低事故中因未佩戴安全帶造成的傷亡，本文提出了基于物聯網技術的客運車乘客安全帶監控系統。 1、理論研究：根據國內外大量的文獻資料，總結已有的安全帶提醒裝置的手段和實現方法，以物聯網技術為基礎，提出相應的研究內容。同時，結合交管部門對于客運車安全帶佩戴的要求、乘客未佩戴安全帶的原因，分析傳統客運車安全帶提醒裝置的不足，提出客運車安全帶監控系統所應解決的關鍵問題。 2、系統總體設計和實現：根據系統功能分析，對客運車乘客安全帶監控系統進行總體設計，，包括系統總體結構設計、系統的傳感器節點組網方案設計、系統的軟硬件設計、系統的低功耗設計、系統的通信協議設計和系統后臺數據庫設計。根據系統總體設計要求，完成了客運車集中控制器和客運中心監控端的實現。其中，客運車集中控制器是在嵌入式實時操作系統μC/OS-Ⅱ的平臺上進行實現的；客運中心監控端是在VC++6.0平臺下采用MFC進行實現的�？瓦\車集中控制器的實現是在無線網絡環境下，通過查詢指令對座椅節點進行數據采集和傳輸，最后客運車集中控制器通過網絡GPRS模塊將座椅數據傳輸給客運中心監控端；客運中心監控端程序實現的是客運中心管理人員的用戶登錄、運行車輛內部安全帶佩戴情況的實時監控、后臺SQL數據庫的操作和數據報表的導出等。 3、系統測試：一，由于基于物聯網的客運車的客運車監控系統的節點多，數據傳輸均建在無線傳輸?shù)幕A上，必須保證所設計通信模塊的功能屬性，即傳輸實時性、傳輸距離、數據丟包率等，通過在多種環境下的測試與分析，測試并驗證通信模塊的性能；二，本文對系統的主要功能進行了試驗驗證，即安全帶實時顯示功能，結果表明本系統滿足項目的要求。
[Abstract]:In 2013, the new traffic regulations made it clear for the first time that all passengers in passenger cars must wear seat belts, otherwise they would be fined. As one of the effective methods to improve the wearing rate of seat belt, every vehicle is equipped with seat belt warning device, but the warning object of the existing safety belt warning device only refers to the driving position and the co-pilot position, but neglects the warning of the passengers in the rear row of the vehicle. For passenger cars, although drivers have traditionally warned back passengers to wear seat belts, the annual reports of passenger vehicle accidents show that some passengers are killed or injured because they are not wearing seat belts. Therefore, in order to increase the wearing rate of passenger vehicle seat belts and reduce the casualties caused by the failure to wear seat belts in accidents, This paper presents a passenger seat belt monitoring system based on Internet of things technology. 1. Theoretical study: according to a large number of literature at home and abroad, summed up the existing means and methods of safety belt warning device, Based on the Internet of things technology, the corresponding research contents are put forward. At the same time, according to the requirements of traffic control departments for passenger vehicle seat belts, and the reasons why passengers do not wear seat belts, this paper analyzes the shortcomings of the traditional passenger vehicle seat belt warning devices. The key problems of passenger vehicle seat belt monitoring system are put forward. 2, the overall design and implementation of the system: according to the system function analysis, the overall design of passenger seat belt monitoring system is carried out, including the overall structure design of the system. The design of sensor node networking scheme, hardware and software design, low power consumption design, communication protocol design and background database design of the system. According to the overall design requirements of the system, the realization of the centralized controller of passenger vehicle and the monitoring terminal of passenger transportation center is completed. The centralized controller of passenger vehicle is implemented on the platform of embedded real-time operating system 渭 C / OS- 鈪

本文編號：2271279