本文關鍵詞： 銑刨機 作業質量 轉子參數 運動參數　出處：《長安大學》2014年碩士論文　論文類型：學位論文

【摘要】：路面銑刨機是瀝青路面養護施工的主要機種之一，主要用于公路、機場、貨場及停車場等瀝青混凝土路面的維修及翻新。銑刨機施工作業時，銑刨轉子直接參與銑削作業，它的性能參數直接影響到銑刨機作業質量的好壞，研究其性能參數對作業質量的影響規律，對提高和改善銑刨機的作業質量有著重要意義，同時也可以為銑刨轉子的生產研制提供參考。 本文圍繞著銑刨機的作業質量與其銑刨轉子的結構參數、運動參數的關系，，進行了以下研究：分析了作業質量的影響因素，對作業質量與轉子結構參數的關系進行了研究；通過對國內外銑刨轉子參數的統計分析，確定了轉子直徑與最大銑刨深度之間的關系；建立了銑削轉角與轉子直徑、銑刨深度的數學模型，借助MATLAB繪制了不同轉子直徑條件下最大切削角與銑削深度的關系曲線；研究分析了螺旋升角、拋料板的安裝對回收率的影響，確定了銑削舊料能夠被集料皮帶收集到的條件，通過建立的行走作業速度與銑刨深度的數學模型，繪制了在防干涉銑削與功率匹配兩種條件下的作業速度與銑刨深度的特征曲線，并求出了最佳銑削點X；根據最佳銑削粒徑范圍得出了用以確定銑削作業速度和轉子轉速的計算公式；利用切削圖，分析了銑削速度對銑削舊料粒徑大小的影響。最后進行銑刨機現場銑削瀝青路面的試驗，對采集到的試驗數據進行了研究分析，得出銑刨深度一定時，當銑削速度為6m/min左右時作業質量最好。
[Abstract]:Pavement milling machine is one of the main kinds of asphalt pavement maintenance and construction, mainly used in the maintenance and renovation of asphalt concrete pavement such as highway, airport, cargo yard and parking lot. Its performance parameters directly affect the quality of the milling machine. It is of great significance to study the influence of the performance parameters on the working quality of the milling machine, and to improve the working quality of the milling machine. At the same time, it can also provide a reference for the production and development of milling and planing rotor. In this paper, the relationship between the working quality of the milling machine and the structural parameters and motion parameters of the milling rotor is studied as follows: the influencing factors of the working quality are analyzed, and the relationship between the working quality and the structural parameters of the rotor is studied; The relationship between the rotor diameter and the maximum milling depth is determined through the statistical analysis of the rotor parameters at home and abroad, and the mathematical model of milling angle, rotor diameter and milling depth is established. The relationship curve between maximum cutting angle and milling depth under different rotor diameters is plotted by MATLAB, the influence of spiral angle and plate installation on the recovery rate is analyzed, and the conditions under which the old milling materials can be collected by aggregate belt are determined. Based on the mathematical model of walking speed and milling depth, the characteristic curves of operation speed and milling depth under two conditions of anti-interference milling and power matching are drawn. The optimum milling point X and the formula used to determine the milling speed and rotor speed are obtained according to the optimum milling particle size range. The effect of milling speed on the particle size of used milling materials is analyzed. Finally, the experiments of milling asphalt pavement by milling machine on the spot are carried out, and the collected test data are studied and analyzed, and the results show that the milling depth is constant. When milling speed is about 6 m / min, the operation quality is the best.
【學位授予單位】：長安大學
【學位級別】：碩士
【學位授予年份】：2014
【分類號】：U418.3

【參考文獻】

相關期刊論文 前10條

1 郭迎福;段明濤;;路面銑刨機銑刨鼓的刀具布置[J];工程機械;2006年05期

2 李芳玉;;銑刨轉子邊刀及邊刀座磨損原因分析及改進[J];工程機械;2009年10期

3 李維維;霍建中;;路面冷銑刨機刀具和刀座磨損形態及成因探析[J];工程機械;2010年12期

4 畢鳳陽;郝晨生;齊曉杰;宮瑩;劉文劍;;路面銑刨刀具的結構與工藝分析[J];哈爾濱工業大學學報;2012年01期

5 張學波;劉巖;;LX2000銑刨機收料室的改進設計[J];建設機械技術與管理;2007年03期

6 喻鋼;;銑刨機防干涉銑削理論及其應用[J];建設機械技術與管理;2008年07期

7 戴玲;喻鋼;;銑刨機刀具防干涉銑削與功率匹配的求解及MATLAB分析[J];建設機械技術與管理;2011年11期

8 周海波;徐克林;;就地?zé)嵩偕鷻C(jī)組銑刨裝置深度控制系統的研究[J];制造業自動化;2006年10期

9 游張平,李自光,鄧習樹,何志勇;路面銑刨機及其發展趨勢[J];建筑機械化;2003年09期

10 李文杰;曾慶良;殷亮;秋實;胡昊;李艷霞;張培友;;用于砂土收集的銑刨轉子刀具排列方式選擇[J];建筑機械化;2011年01期

本文編號：1494639