發布時間：2019-04-17 06:26

【摘要】：使用YAG型光纖激光器對DP590鋼進行激光焊接試驗,研究了焊接接頭的微觀組織和顯微硬度。結果表明:激光輸出功率為3 k W,焊接速度為3、4、5 m/min時,焊接接頭外觀形貌較好,沒有出現裂紋、氣孔。隨著焊接速度的增大,焊接接頭的焊縫區和熱影響區的寬度逐漸減小。焊縫中心的組織為板條狀的馬氏體,靠近焊縫熱影響區的組織為馬氏體和少量的鐵素體,靠近母材熱影響區的組織為馬氏體和大量的鐵素體。接頭焊縫區的顯微硬度明顯高于母材,焊縫中心的最高硬度為380 HV。焊接接頭的硬度從焊縫到母材呈逐漸減小的趨勢。
[Abstract]:The microstructure and microhardness of welded joint of DP590 steel were studied by laser welding experiment with YAG type fiber laser. The results show that when the laser output power is 3 kW, the welding speed is 3, 4, and the welding speed is 5 m/min, the appearance of the welded joint is better, and there are no cracks and pores. With the increase of welding speed, the width of weld zone and heat affected zone of welded joint decreases gradually. The microstructure in the center of the weld is lath martensite, the microstructure near the HAZ is martensite and a small amount of ferrite, and the microstructure near the HAZ of the base metal is martensite and a large number of ferrite. The microhardness of the weld zone is obviously higher than that of the base metal, and the highest hardness in the weld center is 380HV.. The hardness of welded joint decreases gradually from weld to base metal.
【作者單位】： 上海工程技術大學材料工程學院;
【基金】：上海汽車工業科技發展基金資助項目(1404) 上海工程技術大學大學生創新資助項目(A1-5300-16-0502025)
【分類號】：TG457.11

【相似文獻】

相關期刊論文 前10條

1 孟獻民;顯微硬度試驗的對比性[J];兵器材料與力學;1984年03期

2 馬驚生;陳鵬;黃啟震;;煤炭顯微硬度的研究[J];煤炭學報;1987年03期

3 馮詩慶;王紹章;;用顯微硬度和顯微脆度鑒別煤的還原程度[J];煤田地質與勘探;1991年05期

4 蔡兆勛;;全自動顯微硬度試驗系統[J];上海金屬.有色分冊;1992年03期

5 蔡厄,周平南;顯微硬度負荷依存性現象及其本質[J];上海交通大學學報;1998年02期

6 趙所琛,桂運平;顯微硬度的常量和相對比較測試方法[J];金屬學報;1979年01期

7 蔡s，

本文編號：2459178