【摘要】：雙熱絲MAG焊接技術(Double Hot Wires MAG Welding Technology)是一種高效焊接方法。在焊接過程中有一根主焊絲和兩根熱絲。主焊絲和母材之間產生主弧,熱絲加熱電源的兩個輸出端子分別與兩根焊絲連接,經焊接熔池構成閉合回路。該工藝采用電阻熱預熱焊絲,利用熔池的能量最終熔化焊絲,在增大熔敷效率的同時,有效降低焊接熱輸入。研究熱絲電流I_(res)對焊絲熔敷速率的影響規律,并進行厚板的多層擺動焊接。結果表明,隨著I_(res)的增大,焊絲熔化速度增大,并且每一個熱絲電流對應一個最佳熱絲送絲速度范圍,最大熔敷速度可達25 kg/h以上,有效提高了焊接效率。
[Abstract]:Double hot wire MAG welding technology (Double Hot Wires MAG Welding Technology) is an efficient welding method. There is one main wire and two hot wires during the welding process. The main arc is produced between the main welding wire and the base metal. The two output terminals of the hot wire heating power supply are respectively connected with the two welding wires, and the closed loop is formed by the welding pool. In this process, the welding wire is preheated by resistance, and the welding wire is melted by the energy of the weld pool. The welding heat input is reduced effectively while the deposition efficiency is increased. The influence of hot wire current I _ (res) on the deposition rate of welding wire was studied and the multi-layer swinging welding of thick plate was carried out. The results show that with the increase of I _ (res), the wire melting rate increases, and each hot wire current corresponds to an optimum wire feeding speed range, and the maximum deposition speed can reach more than 25 kg/h, which effectively improves the welding efficiency.
【作者單位】： 北京工業大學機械工程與應用電子技術學院;
【分類號】：TG444.7

【相似文獻】

相關期刊論文 前9條

1 李桓,張寶紅,孫國夫,奚道巖;熱絲填充埋弧焊原理及應用[J];焊接學報;1998年01期

2 趙福海;華學明;葉欣;吳毅雄;;熱絲TIG焊方法最新研究進展[J];熱加工工藝;2011年03期

3 易絳弘;熱絲TIG焊──高質量TIG焊與高效率MAG焊的結合[J];電焊機;1996年04期

4 陳克選;張世勤;肖笑;陳響;李述輝;;單電源脈沖熱絲TIG焊控制電路[J];電焊機;2012年01期

5 黃學斌;;鋁合金感應熱絲系統應用及優化[J];機械制造文摘(焊接分冊);2014年02期

6 肖笑;陳克選;宋聚海;王曉非;;單電源脈沖熱絲TIG焊的研究[J];電焊機;2009年06期

7 李進;李剛;楊亞濤;;熱絲TIG焊在核電蒸汽發生器下封頭接管中的應用[J];焊接技術;2012年03期

8 周礦先,徐緒炯,吳青松;自動熱絲TIG焊工藝簡介[J];焊管;1997年05期

9 ;[J];;年期

相關碩士學位論文 前2條

1 王陸釗;熱絲TIG焊的工藝及性能研究[D];江蘇科技大學;2010年

2 趙福海;熱絲TIG焊熱絲溫度分析及溫度場模擬[D];上海交通大學;2012年

，

本文編號：2275839