【摘要】：以非線性有限元軟件Dynaform為平臺,保持凸模與坯料間的摩擦系數不變,分別將凹模與坯料間的摩擦系數取值為0.01,0.02,0.04,0.08和0.1,研究凹模與坯料間的摩擦系數對1716印涂鋁蓋沖壓拉深過程中壁厚分布的影響;再將凹模與坯料間的摩擦系數保持不變,分別將凸模與坯料間的摩擦系數取值為0.1,0.125,0.15,0.17和0.18,研究凸模與坯料間的摩擦系數對1716印涂鋁蓋沖壓拉深過程中壁厚分布的影響。結果表明:1716印涂鋁蓋末次拉深的相對合理摩擦條件是凸模與坯料間靜摩擦系數取0.17,凹模與坯料間動摩擦系數取0.020。同時,生產試驗表明,采用靜摩擦系數為0.17、動摩擦系數為0.020的摩擦條件可以生產出質量合格的產品。
[Abstract]:Based on the nonlinear finite element software Dynaform, the friction coefficient between the punch and the blank is kept unchanged. The friction coefficient between the die and the blank is 0.01 / 0. 02 / 0. 04 / 0. 08 and 0. 1 respectively. The influence of the friction coefficient between the die and the blank on the distribution of the wall thickness in the drawing process of the 1716 coated aluminum cover is studied, and the friction coefficient between the die and the blank is kept unchanged. The friction coefficient between the punch and the blank is 0.1250.150.17 and 0.18, respectively. The influence of the friction coefficient between the punch and the blank on the distribution of the wall thickness during the stamping and drawing of 1716 coated aluminum cover is studied. The results show that the relative reasonable friction conditions for the final drawing of the overcast aluminum cover are as follows: the static friction coefficient between the punch and the blank is 0.17, and the dynamic friction coefficient between the die and the blank is 0.020. At the same time, the production test shows that the product of qualified quality can be produced under the friction condition of static friction coefficient of 0.17 and dynamic friction coefficient of 0.020.
【作者單位】： 四川大學制造科學與工程學院;四川職業技術學院機械工程系;
【基金】：四川省教育廳自然科學重點科研項目(15ZA0347)
【分類號】：TG386.32

【相似文獻】

相關期刊論文 前6條

1 蔣金玉;;反射微波的涂鋁玻璃布[J];玻璃纖維;1983年02期

2 杜明;高溫噴涂鋁[J];輕合金加工技術;1984年07期

3 孫斌先;;環氧噴涂鋁茶壺[J];浙江科技簡報;1984年05期

4 李維英;;油罐涂何顏色最好[J];石油煉制與化工;1958年01期

5 舒中俊;一種單面涂鋁PVC塑料吊頂材料燃燒性能的實驗研究[J];中國塑料;2004年05期

6 ;[J];;年期

，

本文編號：2254324