發布時間：2018-09-08 08:49

【摘要】：為滿足難變形材料軋制實驗研究,開發新型實驗軋機.采用液壓張力缸和液壓夾頭夾持短試樣,實現直拉張力軋制.采用兩臺主電機對上下工作輥單獨傳動和速度調整,實現異步軋制時速度比連續調整.將夾持軋件兩端的夾頭作為正負極,通低電壓大電流,對軋件進行電阻加熱,實現溫軋功能.利用該新型實驗軋機進行驗證實驗.對3%Si無取向硅鋼進行帶張力異步軋制,異步比設定為1.12,總壓下量增大28.4%.對AZ31鎂合金進行帶張力溫軋實驗,厚度由4 mm軋制到0.633 mm,順利完成軋制并得到很好的表面質量.實驗表明,該實驗軋機可以作為難變形材料軋制實驗研究的有力工具.
[Abstract]:A new type of experimental mill was developed to satisfy the experimental research of hard-deformation material rolling. By using hydraulic tension cylinder and hydraulic chuck to clamp short sample, straight tension rolling is realized. The speed ratio of asynchronous rolling is adjusted continuously by using two main motors to drive the upper and lower work rolls separately and adjust the speed. The clamping chuck at both ends of the rolling piece is used as the positive and negative electrode, the low voltage and high current are passed, and the resistance is heated to realize the function of warm rolling. The new experimental mill is used to carry out the verification experiment. The 3%Si non-oriented silicon steel was rolled by asynchronous rolling with tension. The asynchronous ratio was set to 1.12 and the total reduction increased by 28.4kyr. The strip tension warm rolling test of AZ31 magnesium alloy was carried out. The thickness of the alloy was rolled from 4 mm to 0.633 mm, and the good surface quality was obtained. The experimental results show that the rolling mill can be used as a powerful tool for the experimental study of difficult deformation materials.
【作者單位】： 東北大學軋制技術及連軋自動化國家重點實驗室;
【基金】：中央高�；究蒲袠I(yè)務費專項資金資助項目(N120407007,L1507007)
【分類號】：TG333

【相似文獻】

相關期刊論文 前5條

1 孟寶;萬敏;吳向東;周應科;;難變形材料真空環境熱拉深系統的開發與應用(英文)[J];Transactions of Nonferrous Metals Society of China;2012年S2期

2 趙剛要;張冉陽;郭正華;涂善俊;王恩樂;馮占榮;;難變形材料薄壁筒形件強力旋壓研究進展[J];熱加工工藝;2012年23期

3 羅子健，劉東，，姬婉華;基于耗散結構理論的鍛造熱力參數確定方法[J];中國機械工程;1996年03期

4 ;二重將制造世界上最大的模鍛壓機[J];機械研究與應用;2008年02期

5 ;[J];;年期

相關會議論文 前1條

1 李繼貞;陳福龍;王健飛;;航空航天應用難變形材料的旋壓成形[A];第十一屆全國旋壓技術交流大會論文集[C];2008年

本文編號：2230029