發布時間：2018-08-12 13:31

【摘要】：利用雙錐試樣熱壓縮實驗研究了GH738合金的動態再結晶行為,通過有限元軟件計算得到樣品縱剖面應變和溫度的定量分布規律,進而構建合金動態再結晶的動力學曲線,并分析了熱壓縮溫度對再結晶動力學的影響規律。結果表明:將雙錐試樣壓縮至高12 mm時,其縱剖面中心線位置的真應變量呈對稱分布且連續變化,邊緣最低應變量為0.47,心部應變量峰值為2.61,該區域溫度基本保持穩定;動態再結晶比例隨真應變呈"S"形曲線變化,隨著預熱溫度的降低,再結晶形核所需應變量增大,晶粒尺寸減小,但完成再結晶所需應變量無明顯變化。
[Abstract]:The dynamic recrystallization behavior of GH738 alloy was studied by thermal compression test of double cone specimen. The quantitative distribution of strain and temperature in the longitudinal section of the sample was calculated by finite element software, and then the dynamic curve of dynamic recrystallization of the alloy was constructed. The effect of hot compression temperature on recrystallization kinetics was analyzed. The results show that the true strain of the center line of the longitudinal profile is symmetrical and continuously varied when the biconical specimen is compressed to 12mm, the lowest strain at the edge is 0.47, the peak value of the central strain is 2.61, and the temperature in the region is basically stable. The dynamic recrystallization ratio changes with the true strain as "S" curve. With the decrease of preheating temperature, the strain of recrystallization nucleation increases and the grain size decreases, but the required strain to complete recrystallization has no obvious change.
【作者單位】： 江蘇省先進結構材料與應用技術重點實驗室;南京工程學院材料工程學院;
【基金】：國家自然科學基金青年科學基金項目(No.51301085) 南京工程學院引進人才科研啟動基金項目(No.YKJ201306)
【分類號】：TG132.3

【相似文獻】

相關期刊論文 前7條

1 劉興富;;雙錐零件特性尺寸的測量[J];機械工業標準化與質量;2006年08期

2 劉興富;;雙錐零件特性尺寸的測量——一個由基準引發的測量問題[J];計量技術;2006年04期

3 馮可華;雙錐回轉體零件的成形[J];模具工業;2003年03期

4 馮可華;雙錐回轉體零件的成形及模具設計[J];模具制造;2002年10期

5 張光輝;;花鍵孔齒輪精車用雙錐漲套結構設計[J];機械;1993年05期

6 張韶華,徐偉;新型鍛壓機——雙錐輥軸向模軋機研制[J];鍛壓裝備與制造技術;2004年04期

7 ;[J];;年期

，

本文編號：2179202