本文選題：水下焊接　切入點：濕法焊條電弧焊　出處：《焊接學報》2017年04期

【摘要】：通過對潛水員焊工的培訓,成功實現了不同接頭形式的水下濕法手工多層多道焊,并且在渤海海域的11,22 m兩個水深分別進行了對接接頭平焊、搭接接頭橫焊及立焊和T形接頭立焊及船形位置焊的焊接試驗.結果表明,在兩種水深的對接接頭和搭接接頭中都未發現夾渣、氣孔及未熔合等缺陷,并且兩種水深的對接接頭和搭接接頭在各項力學性能指標上都滿足AWS D3.6 M:2010關于B級接頭的要求.與11 m水深的焊縫相比,22 m水深的焊縫柱狀晶區的針狀鐵素體減少,塊狀鐵素體明顯增多.兩種水深接頭的熱影響區粗晶區組織差異不大,主要由板條狀馬氏體組成.
[Abstract]:Through the training of divers, the underwater wet multi-layer multi-pass welding with different joint forms was successfully realized, and the butt welding was carried out in two water depths of 1122 m in Bohai Sea, respectively. Welding tests of lap joint transverse welding and vertical welding and T-joint vertical welding and ship position welding. The results show that there are no defects such as slag inclusion, porosity and non-fusion in the butt joints and lap joints of two kinds of water depth. The mechanical properties of two kinds of water depth butt joints and lap joints meet the requirements of AWS D 3.6 M: 2010 for B grade joints. Compared with the weld with 11 m water depth, the acicular ferrite in the columnar crystal zone of the weld with water depth of 22 m is reduced. The structure of the heat affected zone of the two water depth joints is not different from that of the heat affected zone, and it is mainly composed of lath martensite.
【作者單位】： 天津大學材料科學與工程學院;天津大學天津市現代連接技術重點實驗室;海洋石油工程股份有限公司;
【分類號】：TG456.5

【相似文獻】

相關期刊論文 前10條

1 黎咸西;熊震宇;;基于視覺傳感的多層多道焊縫圖像特征的識別[J];南昌航空大學學報(自然科學版);2011年01期

2 李慧娟;黃振華;張京燾;;厚板多層多道焊的數值模擬分析[J];宇航材料工藝;2007年05期

3 李慧娟;黃振華;李正任;;多層多道焊焊接工藝數值模擬技術[J];焊接技術;2010年11期

4 胥國祥;杜寶帥;董再勝;朱靜;;厚板多層多道焊溫度場的有限元分析[J];焊接學報;2013年05期

5 翟紫陽;王克鴻;;超高強鋼板多層多道焊溫度場有限元分析[J];電焊機;2014年05期

6 危文灝;，

本文編號：1666445