本文關鍵詞： 合肥光源 全站儀 激光跟蹤儀 控制網 精度分析 模擬計算平差計算 精度評估 SA USMN 三維網平差　出處：《合肥工業大學》2013年碩士論文　論文類型：學位論文

【摘要】：合肥光源升級改造工程一級和二級控制網的建立是基于LeicaTDA5005全站儀和激光跟蹤儀，合肥光源的磁鐵點位精度達到微米級，其高精度的要求已達到計量學的精度，即用精密工程測量學的方法，用高精度的現代儀器，達到計量學的精度指標；合肥光源升級改造工程的準直測量首先必須建立高精度的控制網，再通過控制網對磁鐵點位進行定位和調試。而本文主要是對一級和二級控制網進行施測方案設計、模擬計算并且通過實際測量數據進行平差計算，從而建立穩定、合理和高精度的控制網。本論文的主要內容如下： 1、針對合肥光源進行簡單的介紹，并且闡述了合肥光源升級改造的必要性；同時對合肥光源升級改造工程的準直測量進行概述。 2、闡述了合肥光源升級改造工程建立一級和二級控制網的目的，對一級和二級控制網進行方案設計、精度分析和模擬計算。 3、介紹了合肥光源升級改造工程一級控制網的所用儀器和實測過程，并根據一級網的實測數據進行平差計算和精度評估。 4、介紹了合肥光源改造工程二級控制網的實測過程和施測難點，結合激光跟蹤儀測量數據采用Spatial Analyzer（SA）軟件的統一空間測量網絡法（Unified Spatial Metrology Network，USMN）和三維網平差法進行數據處理，并對兩種方法的數據處理結果進行對比分析，，從而對二級控制網進行精度評估。
[Abstract]:The establishment of primary and secondary control network of Hefei Light Source upgrading Project is based on LeicaTDA5005 total station instrument and laser tracker. The precision of magnetic spot position of Hefei light source reaches micron level, and its high precision requirement has reached metrology precision. That is to say, the precision index of metrology is achieved by means of precision engineering surveying method and modern instrument with high precision, and the collimation measurement of Hefei light source upgrading project must first establish a high-precision control network. Then the magnet spot is located and debugged through the control network. In this paper, the primary and secondary control networks are designed, simulated and adjusted through the actual measurement data, thus the stability is established. The main contents of this paper are as follows:. 1. The light source of Hefei is introduced briefly, and the necessity of upgrading the light source in Hefei is expounded. At the same time, the collimation measurement of the upgrading project of light source in Hefei is summarized. 2. The purpose of establishing primary and secondary control networks in Hefei Light Source upgrading Project is expounded. The scheme design, precision analysis and simulation calculation of primary and secondary control networks are carried out. 3. The instrument used in the primary control network of Hefei Light Source upgrading Project and the measurement process are introduced, and the adjustment calculation and accuracy evaluation are carried out according to the measured data of the first class light source. 4. The measurement process and difficulties of the secondary control network of Hefei Light Source Reconstruction Project are introduced. The unified spatial measurement network method Unified Spatial Metrology Network (USMN) and the three-dimensional network adjustment method are used to process the data of laser tracker using Spatial Analyzer-SAsoftware. The data processing results of the two methods are compared and analyzed so as to evaluate the accuracy of the two-level control network.
【學位授予單位】：合肥工業大學
【學位級別】：碩士
【學位授予年份】：2013
【分類號】：P22

【參考文獻】

相關期刊論文 前10條

1 于成浩;柯明;趙振堂;;精密工程測量中全站儀三角高程精度分析[J];北京測繪;2006年03期

2 李廣云;工業測量系統最新進展及應用[J];測繪工程;2001年02期

3 于成浩;柯明;趙振堂;;激光跟蹤儀測量精度的評定[J];測繪工程;2006年06期

4 于成浩;柯明;;基于激光跟蹤儀的三維控制網測量精度分析[J];測繪科學;2006年03期

5 于成浩;柯明;趙振堂;;提高激光跟蹤儀測量精度的措施[J];測繪科學;2007年02期

6 于成浩;董嵐;柯明;杜涵文;殷立新;趙振堂;黃開席;;大尺寸激光跟蹤儀三維控制網平面精度研究[J];測繪科學;2008年02期

7 陳繼華;黃桂平;李廣云;;一種新的經緯儀/全站儀工業測量系統標定算法[J];測繪通報;2006年08期

8 李廣云;非正交系坐標測量系統原理及進展[J];測繪信息與工程;2003年01期

9 于成浩;柯明;杜涵文;;大尺寸空間中激光跟蹤儀和水準儀的高程測量結果比較[J];工程勘察;2007年06期

10 劉建新;馬強;楊再華;;激光跟蹤測量系統及其在航天器研制中的應用[J];航天器環境工程;2008年03期

本文編號：1511572