本文選題：斷路器　切入點：脫扣過程　出處：《河北工業大學》2014年碩士論文　論文類型：學位論文

【摘要】：低壓電器在電器行業中應用非常廣泛，它在配電、保護人身安全中起著非常重要的作用，能否可靠分斷是研究斷路器的重要方面，由于斷路器的分斷過程比較復雜，涉及的領域比較多，，因此對其進行分析和研究是一個重要的課題，本文以TM-30/100型塑殼斷路器為主要研究對象，基于ANSYS、Pro/E、ADAMS三個軟件的功能，對斷路器進行分斷過程的聯合仿真，具體分以下幾個方面： 一、根據實際的尺寸在Pro/E中建立斷路器的模型，再將模型導入到ANSYS中，首先對雙金屬片進行有限元熱分析，將分析結果作為動力學仿真中雙金屬片自由端的位移。接著計算不同電流和開距下電磁脫扣機構的電磁力和動靜觸頭間的電動斥力，作為力的載荷加載到ADAMS中。 二、將模型通過專用的軟件導入到ADAMS中，依據前面分析的數據進行加載后，分別對斷路器的延時和瞬態分斷過程進行動力學仿真，觀察觸頭運動情況，及電動斥力在短路狀態時對觸頭分斷過程的影響。
[Abstract]:Low-voltage electrical apparatus is widely used in electrical industry, it plays a very important role in distribution and protection of personal safety. It is an important aspect to study circuit breaker whether it can break reliably, because the breaking process of circuit breaker is more complicated. There are many fields involved, so it is an important subject to analyze and study the circuit breaker. This paper takes the TM-30/100 type plastic case breaker as the main research object, and based on the functions of ANSYSU Prop / E / Adams software, simulates the breaking process of the circuit breaker. It can be divided into the following aspects:. First, the model of circuit breaker is established in Pro/E according to the actual size, and then the model is imported into ANSYS. Firstly, the finite element thermal analysis of bimetallic sheet is carried out. The results are taken as the displacement of the free end of the bimetallic sheet in the dynamic simulation. Then the electromagnetic force of the electromagnetic release mechanism and the electric repulsion force between the static and static contacts under different current and open distance are calculated and loaded into the ADAMS as the load of the force. Secondly, the model is imported into ADAMS through special software. After loading according to the data of the previous analysis, the dynamic simulation of the circuit breaker's delay and transient breaking process is carried out, and the contact motion is observed. And the effect of electric repulsion force on the breaking process of contact in short circuit state.
【學位授予單位】：河北工業大學
【學位級別】：碩士
【學位授予年份】：2014
【分類號】：TM561

【參考文獻】

相關期刊論文 前6條

1 何瑞華;;我國低壓斷路器現狀與發展動向[J];電氣技術;2009年06期

2 周志敏;小型斷路器的發展與應用[J];電氣開關;2002年05期

3 何瑞華,尹天文;我國低壓電器行業現狀與發展趨向[J];低壓電器;2004年01期

4 李震彪;鄭必成;何整杰;Makoto Hasegawa;;對流與輻射對電磁繼電器內部溫度場影響的仿真研究(英文)[J];電工材料;2009年02期

5 李文俊;董星濤;王春博;孫磊;盧德林;;基于SLS技術的非均質材料零件成型研究[J];輕工機械;2012年02期

6 張敬菽,陳德桂,劉洪武,向洪崗,紐春萍;計及電動斥力效應的低壓塑殼斷路器機構動力學仿真[J];西安交通大學學報;2004年04期

本文編號：1561178