發布時間：2019-06-25 07:58

【摘要】：隨著中國城市交通建設的飛速發展,彎橋已經成為現代交通基礎設施的重要橋型。彎橋由于受力性能復雜,力學性能除受橋梁跨度、截面形式和配筋率的影響外,還要受到曲率半徑、圓心角、梁寬及彎扭剛度比的影響,十分復雜。在現行規范中,對彎橋的承載力檢測方案沒有明確給出,其承載力檢測理論和技術方面還存在諸多問題尚未解決,這對于正確評估這類橋梁的工作性能及承載能力具有重大影響。本文首先介紹了彎橋的力學特性、構造特點及理論分析方法。以30m+40m+30m的三跨連續彎箱梁橋為例,采用有限元軟件Midas civil對彎橋進行梁格法分析,結合有限元實體單元軟件Midas FEA建立實體單元模型,進行了大量的計算和分析比較;第二,通過數值解得到的相關數據,分析比較了相關試驗工況的荷載效應、剪力滯的分布,得出彎橋中由于扭矩的存在加強了箱梁的剪力滯效應,并通過試驗實測值驗證了結論的正確性;第三,通過對控制截面應力大小,位置和梁底沿半徑切線方向的彎拉應力的分析比較,確定了在彎橋中梁底應力可代替主應力起到控制作用,從而確定了應變片的粘貼位置及方向;第四,計算分析了彎橋截面中扭矩所產生的剪應力對于彎橋承載力檢測的影響,以及應變片因粘貼偏角的誤差公式推導。根據以上分析研究結果,提出了改善彎橋試驗檢測效果的相關方法,這對于提高彎橋檢測效果、評價彎橋的工作性能及承載能力的準確性都具有重大的意義。
[Abstract]:With the rapid development of urban traffic construction in China, curved bridge has become an important bridge type of modern traffic infrastructure. Because of the complexity of mechanical properties of curved bridge, the mechanical properties are not only affected by bridge span, section form and reinforcement ratio, but also affected by curvature radius, circular center angle, beam width and bending-torsional stiffness ratio. In the current code, the bearing capacity detection scheme of curved bridge is not given clearly, and there are still many problems to be solved in the theory and technology of bearing capacity testing, which has a great influence on the correct evaluation of the working performance and bearing capacity of this kind of bridge. In this paper, the mechanical properties, structural characteristics and theoretical analysis methods of curved bridges are introduced. Taking 30m 40m 30m three-span continuous curved box girder bridge as an example, the finite element software Midas civil is used to analyze the curved bridge by beam lattice method. Combined with the finite element entity element software Midas FEA, the solid element model is established, and a large number of calculation, analysis and comparison are carried out. Secondly, through the relevant data obtained by numerical solution, the load effect and shear lag distribution of related test conditions are analyzed and compared, and it is concluded that the shear lag effect of box girder is strengthened due to the existence of torque in curved bridge, and the correctness of the conclusion is verified by the measured values. Thirdly, by analyzing and comparing the stress of the control section, the position and the bending tensile stress of the beam bottom along the tangent direction of the radius, it is determined that the stress at the bottom of the beam can replace the principal stress in the curved bridge, thus determining the bonding position and direction of the strain gauge. Fourth, the influence of the shear stress caused by the torque in the section of the curved bridge on the bearing capacity of the curved bridge is calculated and analyzed, and the error formula of the strain gauge due to the sticking deflection angle is deduced. According to the above analysis and research results, the related methods to improve the test and detection effect of curved bridge are put forward, which is of great significance to improve the detection effect of curved bridge and evaluate the working performance and bearing capacity of curved bridge.
【學位授予單位】：重慶交通大學
【學位級別】：碩士
【學位授予年份】：2015
【分類號】：U441.2;U446

【參考文獻】

相關期刊論文 前1條

1 蔣志剛;羅旗幟;;雙箱單室箱梁橋頂板橫向彎矩分析[J];中國公路學報;1992年01期

相關碩士學位論文 前1條

1 紀軒彪;彎梁橋力學性能及施工監控研究[D];蘭州交通大學;2011年

，

本文編號：2505525