【摘要】：將優化設計與可靠性理論相結合進行門式卸車機的結構可靠性分析.利用ANSYS Workbench進行參數化實體建模,采用中心復合設計擬合響應面并進行參數靈敏度分析,在此基礎上分別使用Screening,MOGA及NLPQL 3種算法對參數尺寸進行優化和對比分析,得到最佳設計方案,在保證滿足強度要求的條件下,減小卸車機體積.再根據優化分析的結果,以最大等效應力不超過材料許用應力為可靠性評定指標,使用六西格瑪分析技術比較模型優化前后的結構可靠性,優化后的結構可靠性有所提高.在分析結構輕量化問題的同時考慮了其安全可靠性要求,為卸車機的制造與優化改進提供了理論指導.
[Abstract]:The structural reliability analysis of the door unloader is carried out by combining the optimal design with the reliability theory. Parametric solid modeling is carried out with ANSYS Workbench, response surface is fitted by central composite design and parameter sensitivity analysis is carried out. On the basis of this, Screening,MOGA and NLPQL algorithms are used to optimize and compare the parameter size, respectively. The optimal design scheme is obtained, and the volume of the unloading machine is reduced under the condition of satisfying the intensity requirement. According to the results of optimization analysis, the maximum equivalent stress is not more than the allowable stress of the material as the reliability evaluation index, and the structural reliability before and after the optimization is compared by using six Sigma analysis technique, and the structural reliability after optimization is improved. The requirement of safety and reliability is taken into account when analyzing the structural lightweight problem, which provides theoretical guidance for the manufacture and optimization improvement of the unloading machine.
【作者單位】： 大連交通大學交通運輸工程學院;大連交通大學機械工程學院;
【基金】：國家自然科學基金資助項目(11272070) 遼寧省自然科學基金資助項目(2014028020) 遼寧省教育廳科學研究資助項目(JDL2016001) 大連市科技開發資助項目(2015A11GX026)
【分類號】：TH24

【相似文獻】

相關期刊論文 前4條

1 劉煥森;鏈斗式卸車機的功率選擇[J];起重運輸機械;1975年05期

2 班善麟;鐵路卸車機的防塵裝置[J];起重運輸機械;1983年03期

3 夏靜,張石平;數字化制造技術在卸車機設計中的應用[J];煤礦機械;2005年07期

4 徐孝飛;李祥平;蘇飛;王斌;林曉海;;新型自動液壓卸車機的研制[J];科技傳播;2014年10期

，

本文編號：2313237