【摘要】：隨著社會生活水平的提高以及人口老齡化問題日趨嚴峻,各種誘發因素,比如高血脂、高血壓、肥胖等,都會引起血管發生硬化,導致血管狹窄,由此引發的各類心血管疾病威脅著人們的生命健康。開展病灶部位血流動力學的研究,對于研究其發病機理及臨床醫生手術方案的確定具有重要的實際意義。本文搭建了可模擬生理條件下的動脈血流動力學環境、參數可控的體外試驗臺,利用高精度的壓力傳感器監測正常股動脈及病變股動脈內的血液壓力。作為試驗研究的補充,以股動脈血管為原型,建立血管壁/血液耦合模型,對正常血管、孤立性、節段性和彌漫性病變血管四種情況進行數值模擬,分析血管壁的壁面剪切力分布和變形情況,以及管壁對內部血液流場的影響。具體展開以下工作:(1)研究并確定了血液非定常流動的雙向流固耦合分析方法。血液在流動過程中,由于黏性的影響,會對血管壁產生較大的切應力,可將血液視為黏性流體。在血流動力學研究中,牛頓流體與非牛頓流體對所得結果影響并不大,誤差不到2%,故本文數值模擬所用的流體為牛頓流體,試驗流體用水和甘油的混合溶液(牛頓流體)代替血液。試驗是在壓強和溫度變化較小的情況下進行的,所以可將流體視為不可壓縮流體。運用雷諾數公式,計算得出在體股動脈的最大雷諾數約為1474~1942,均小于2300,故本文選用Laminar模型。血管為薄壁、各向同性、無滲透、無滑移(no slip)的線彈性直圓管。(2)搭建了管內脈動壓力測量試驗臺,該試驗臺由電腦、電源、伺服電機、驅動器、PLC控制器、滾珠絲桿、注射器、微型壓力傳感器和數據采集器組成。PLC和驅動器通過上機程序控制伺服電機的運行。注射器固定安裝在滾珠絲桿滑塊上,伺服電機連接滾珠絲桿,從而控制注射器桿的進給速度。利用綜合精度為±0.2%的微型壓力傳感器測量血管內脈動壓力值,并用數據采集器獲取數據�；讵M窄股動脈簡化模型參數要求,將人體真實血管模型幾何尺寸放大3.2倍,制備了血管試驗樣件。通過血管狹窄率公式,制作出孤立性、節段性、彌漫性血管和狹窄率為40%、60%、80%的病變血管模型。采用拉伸試驗機測量血管的彈性模量,其值為1.62×106Pa。通過試驗對比分析正常及病變股動脈兩監測點處的壓力差可以看出,股動脈的壓力隨時間的變化范圍和趨勢與入口速度變化趨勢存在緊密的聯系。隨著速度的增大,脈沖壓力達到峰值的數值變小。狹窄段區域越長,狹窄段前后的壓力差幅值變化越大。狹窄度不同,病變血管壓力差達到的幅值也不同,狹窄度為80%的血管脈動壓力幅值最大。狹窄區域后端壓力差的增大,導致血管內壁損傷,易引起其它未發病部位的病變。(3)應用Solidworks軟件構建血管的三維CAD模型,采用ICEM對固體和流體域劃分網格。應用ANSYS軟件,模擬分析了人工血管監測點處壓力差的大小,并與試驗結果做了對比,發現狹窄段前后端的試驗結果幅值比模擬結果稍大且達到峰值的時刻稍微滯后,但基本變化一致,確定了數值模擬計算方法的可行性。因此,本文所采取的流固耦合數值模擬方法可用來模擬分析人體正常股動脈和病變股動脈內的血流動力學特性。(4)對比分析正常及病變股動脈壓力、速度、壁面切應力、血管形變、速度流線等參數可以看出,正常血管的壓力和速度呈均勻性變化,股動脈狹窄造成狹窄處速度增大。狹窄后區域有渦流形成,對管壁造成損傷,加速了其它未發病部位的病變。在整個心動周期內,病變血管的狹窄處壁面切應力值較大,剝離內皮細胞,導致脂質等大分子物質沉附、累積在細胞損傷處。血管狹窄后區域管壁變形最大,管壁出現疲勞效應,易導致血管破裂。
[Abstract]:With the improvement of social living standards and the increasing severity of population aging problem, all kinds of inducing factors, such as hyperlipidemia, hypertension, obesity, will cause vascular sclerosis, resulting in vascular stenosis, resulting in a variety of cardiovascular diseases threatening people's lives and health. It is of great practical significance to study the pathogenesis and determine the operation plan of clinicians.In this paper, an in vitro test-bed with controllable parameters and simulated hemodynamic environment of arteries under physiological conditions was set up to monitor the blood pressure in normal femoral artery and diseased femoral artery with high precision pressure sensor. In order to analyze the distribution and deformation of wall shear force and the influence of wall on the internal blood flow field, the following work was carried out: (1) To study and determine the effect of wall on the internal blood flow field. A bi-directional fluid-solid coupling method for the analysis of unsteady blood flow is presented.During the process of blood flow, due to the influence of viscosity, a large shear stress will occur on the wall of the blood vessel and the blood can be regarded as a viscous fluid.In the study of hemodynamics, Newtonian and non-Newtonian fluids have little influence on the results, and the error is less than 2%. The fluid to be used is a Newtonian fluid. The mixed solution of water and glycerol (Newtonian fluid) is used to replace the blood. The experiment is carried out under the condition of small pressure and temperature change, so the fluid can be regarded as incompressible fluid. The maximum Reynolds number of the femoral artery in vivo is calculated by using Reynolds number formula, which is about 1474-1942, and is less than that of the femoral artery in vivo. In this paper, the Laminar model is used. The blood vessels are thin-walled, isotropic, impermeable and no-slip linear elastic straight circular tubes. (2) A test-bed for measuring the fluctuating pressure in tubes is built. The test-bed consists of a computer, a power supply, a servo motor, a driver, a PLC controller, a ball screw, a syringe, a micro-pressure sensor and a data collector. The actuator controls the operation of the servo motor by a program on the computer.The syringe is fixed on the ball screw slider and the servo motor is connected to the ball screw to control the feed speed of the syringe rod.The pulsating pressure in the blood vessel is measured by a micro-pressure sensor with a comprehensive accuracy of (+0.2%) and the data is obtained by a data collector. The parameters of the simplified model of narrow femoral artery were enlarged by 3.2 times the geometric size of the real blood vessel model, and the vascular test sample was prepared. The pressure difference between normal and diseased femoral arteries was compared and analyzed. It was found that the range and trend of femoral arterial pressure with time were closely related to the trend of inlet velocity. The greater the amplitude of pressure difference is, the different the degree of stenosis is, the greater the amplitude of pressure difference is. The amplitude of pressure difference is 80% of the stenosis. ICEM was used to mesh the solid and fluid domains. ANSYS software was used to simulate and analyze the pressure difference at the monitoring point of artificial blood vessel. The results were compared with the experimental results. It was found that the amplitude of the experimental results at the front and back of the narrow segment was slightly larger than that of the simulation results and the time lagged slightly when the peak value was reached, but the basic changes were consistent. Therefore, the fluid-solid coupling numerical simulation method adopted in this paper can be used to simulate and analyze the hemodynamic characteristics of normal and diseased femoral arteries. (4) Comparing and analyzing the normal and diseased femoral arteries pressure, velocity, wall shear stress, vascular deformation, velocity streamline and other parameters can be seen, normal blood vessels. The stenosis of the femoral artery results in an increase in the velocity of the stenosis. Eddies form in the stenosis area, causing damage to the wall of the vessel and accelerating the pathological changes of other non-pathogenic sites. After vascular stenosis, the wall deformation is the greatest, and fatigue effect appears on the wall, which is easy to lead to vascular rupture.
【學位授予單位】：吉林大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：R54

【參考文獻】

相關期刊論文 前10條

1 譚澤輝,郭靜萱,邵茂剛,葉大均;流場對高脂喂養家兔動脈粥樣硬化形成的影響[J];生物醫學工程學雜志;1994年03期

2 羅小玉,匡震邦;動脈局部狹窄時脈動流的有限元分析[J];力學學報;1992年03期

3 伍時桂,胡利民,王家權;狹窄動脈中的非線性脈動流的數值研究[J];醫用生物力學;2000年02期

4 ;Mechanical model of vulnerable atherosclerotic plaque rupture[J];Science in China(Series G:Physics,Mechanics & Astronomy);2004年04期

5 于風旭;石應康;鄧萬權;陳槐卿;安琪;郭應強;;頸動脈分叉管模型流場分布的PIV測量[J];生物醫學工程學雜志;2007年01期

6 蘇海軍;張鵬飛;張梅;張運;;動脈粥樣硬化斑塊失穩破裂簡化模型的高階動力學研究[J];中國生物醫學工程學報;2006年03期

7 于風旭;廖斌;石應康;鄧明彬;李新;譚善文;;體外人頸動脈血管分叉模型的建立[J];四川大學學報(醫學版);2007年06期

8 顧媛;酈鳴陽;沈力行;喻洪流;丁皓;趙改平;;狹窄動脈流固耦合模型Ansys/CFX數值的有限元分析[J];中國組織工程研究與臨床康復;2008年52期

9 蘇海軍;張鵬飛;陳文強;張梅;張運;;動脈粥樣硬化斑塊的形態學研究及識別[J];中國科學(G輯:物理學 力學 天文學);2008年05期

10 劉書明;常碩;;中國人口年齡結構特征與變化趨勢分析——基于1995～2014年數據的實證研究[J];西北人口;2017年01期

相關博士學位論文 前3條

1 馬燕山;人體動脈的計算流體力學模擬與分析[D];河北醫科大學;2016年

2 邱曉寧;顱頸動脈植入支架后的血流動力學數值模擬與PIV實驗研究[D];上海交通大學;2014年

3 王家權;動脈粥樣硬化的流體力學機理的理論研究和數值模擬研究[D];北京工業大學;2002年

相關碩士學位論文 前7條

1 楊茹雪;髂動脈至股深動脈腔內成形術治療下肢動脈硬化閉塞癥患者療效及并發癥[D];吉林大學;2015年

2 劉鄭琦;局部狹窄動脈流變特性的流固耦合分析[D];北京交通大學;2014年

3 李艷君;基于動脈粥樣硬化的流固耦合模型動力學分析[D];山東大學;2012年

4 王青;顱內動脈瘤血液動力學的數值模擬研究[D];上海交通大學;2010年

5 李瑩;局部狹窄對動脈血液流動的影響研究[D];清華大學;2008年

6 劉金龍;分叉管脈動流的數值模擬與實驗研究[D];上海交通大學;2008年

7 豆中強;動脈血管中脈動血流的數值模擬[D];重慶大學;2006年

，

本文編號：2235452